A long workpiece, with the length-to-dimeter ratio that exceeds factor 10, is to be machined. Which workholding should provide the lowest deflection? Collet in the spindle and a live center in the tailstock Chuck on the spindle, a live center in the tailstock, and a follower rest Mandrel Solid center with a dog and a dog plate on the spindle, a live center in the tailstock Faceplate

A long workpiece, with the length-to-dimeter ratio that exceeds factor 10, is to be machined. Which workholding should provide the lowest deflection? Collet in the spindle and a live center in the tailstock Chuck on the spindle, a live center in the tailstock, and a follower rest Mandrel Solid center with a dog and a dog plate on the spindle, a live center in the tailstock Faceplate

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter4: Drill Press

Section4.2: Tools, Toolholding, And Workholding For The Drill

Problem 12RQ: Which would be the best workholding device for holding a 3/4" 12" 14" flat plate for drilling a...

See similar textbooks

Similar questions

Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a feed rate of 0.004".
Two identical cylindrical jobs are turned using (a) a round nosed tool of nose radius 2 mm and (b) a sharp corner tool having principal cutting edge angle = 45° and auxiliary cutting edge angle = 10° If the operation is carried out of the teed of 0.08 mm/rev will Find the height at micro irregularities on the machined surfaces (in mm) in the two cases.
With neat sketches explain the hydraulic quick return mechanism used on a shaper?
ME 408 - Machine Shop Theory and Practice Describe the step-by-step procedure in turning a taper using compound rest method.
List three benefits of holding a workpiece between centers.
In a crank and slotted lever quick return motion mechanism shown in Fig. for Q. No.1(c), the distance between the fixed centers is 224 mm and the length of thedriving crank is 126 mm. Find the inclination of the slotted bar with the vertical inthe extreme position and the time ratio of cutting stroke to the return stroke.If the length of the slotted bar is 442 mm, find the length of the stroke if the line ofstroke passes through the extreme positions of the free end of the lever.
Mention the difference between Shaper machine and planer machine?
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
I need problem 8 answered pertaining to the print and sequence of operations that is both provided.
In a crank and slotted lever quick return mechanism, as shown in Fig. 2, the driving crank length is 75 mm. The distance between the fixed centres is 200 mm and the length of the slotted lever is 500 mm. Find the ratio of the times taken on the cutting and idle strokes. Determine the effective stroke also
Through holes of 10 mm diameter are to be drilled in a steel plate of 20 mm thickness. Drill spindle speed is 300 rpm, feed 0.2 mm/rev and drill point angle is 120° .Assuming drill overtravel of 2 mm. Calculate the time for producing a hole.
Which would be the best workholding device for holding a 3/4" 12" 14" flat plate for drilling a series of holes through the large surface of the plate?