A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 Ib, a horizontal shear force of V = 260 lb, and a concentratedtorque of T = 1450 lb-in., acting in the directions shown. Assume L = 7.3 in. Section properties for the shaft are A = 1.3273 in.?, J=0.2804 in.“, ly =1,= 0.1402 in.“, and Q = 0.1831 in.3. Determine the normal and shear stresses at point H, and show these stresses on astress element.HKTAnswer:Oy =ipsiTyz =ipsi

Answered: A 1.30-in.-diameter solid shaft is…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.3P: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0...

See similar textbooks

Similar questions

A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A stepped shaft (see figure) has diameter D2= 1.5 in, and a full quarter-circular fillet. The allowable shear stress is 15,000 psi and the load T = 4800 1b-in. What is the smallest permissible diameter D1?
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (see figure), (a) If the allowable shear stress in the shaft is 43 MPa, what is the maximum torque (T0)max that may be applied at section C? (b) Find (ï^),^ if the maximum angle of twist is limited to 1.85', Let G = 28 GPa.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS