A 10-cm diameter well fully penetrates an unconfined aquifer that is 40.0 m thick. The drawdown at thewell is 15.0 m. The hydraulic conductivity of the aquifer is 5.0 × 10-6 m · s-1. Assume steady flow. Whatis the allowable pumping rate to ensure that the drawdown at a well that is 100.0 m from the pumping welldoes not exceed 5.0 m?(a) 0.0063 m³.s-1(b) 0.063 m³ .s-!(c) 0.16 m3(d) 1.6 m3 - s-!

Given Data The diameter of the well is: d=10 cm The thickness of the unconfined aquifer is: t=40 m…

A 10-cm diameter well fully penetrates an unconfined aquifer that is 40.0 m thick. The drawdown at the well is 15.0 m. The hydraulic conductivity of the aquifer is 5.0 × 10-6 m · s-!. Assume steady flow. What is the allowable pumping rate to ensure that the drawdown at a well that is 100.0 m from the pumping well does not exceed 5.0 m? (a) 0.0063 m³.s-1 (b) 0.063 m³ .s-! (c) 0.16 m³ - s-! (d) 1.6 m³ · s-I

A 10-cm diameter well fully penetrates an unconfined aquifer that is 40.0 m thick. The drawdown at the well is 15.0 m. The hydraulic conductivity of the aquifer is 5.0 × 10-6 m · s-!. Assume steady flow. What is the allowable pumping rate to ensure that the drawdown at a well that is 100.0 m from the pumping well does not exceed 5.0 m? (a) 0.0063 m³.s-1 (b) 0.063 m³ .s-! (c) 0.16 m³ - s-! (d) 1.6 m³ · s-I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An inverted 3-m-high conical container is initially filled with 2-m-high water. At time t = 0, a faucet is opened to supply water into the container at a rate of 3 L/s. At the same time, a 4-cm-diameter hole with a discharge coefficient of 0.90 at the bottom of the container is opened. Determine how long it will take for the water level in the tank to drop to 1-m.
Pump Horsepower in Brine System. A pump pumps 0.200 ft3/s of brine solution having a density of 1.15 g/cm3 from an open feed tank having a large cross-sectional area. The suction line has an inside diameter of 3.548 in. and the discharge line from the pump a diameter of 2.067 in. The discharge flow goes to an open overhead tank, and the open end of this line is 75 ft above the liquid level in the feed tank. If the friction losses in the piping system are 18.0 ft lbf/lb m, what pressure must the pump develop and what is the horsepower of the pump if the efficiency is 70%? The flow is turbulent.
A piezometer and a Pitot tube are tapped into a 3-cmdiameter horizontal water pipe, and the height of the water columris are measured to be 20 cm in the piezometer and 35 cm in the Pitot tube (both measured from the top surface of the pipe). Determine the discharge at the center of the pipe. A) 0.0012 m3/s B) 0.1 m3/s C) 10 m3/s D) 1.716 m3/s E) 12.13 /s
In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.55 m3/s through a 200-m-long, 0.35-m-diameter cast iron pipe. The elevation difference between the free surface of the reservoir and the turbine discharge is 140 m, and the combined turbine–generator efficiency is 85 percent. Disregarding the minor losses because of the large length-to-diameter ratio, determine the electric power output of this plant.
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is X= 5 m long and has a 6-cm diameter, while the second pipe is 5 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate. (The density and dynamic viscosity of water at 15°C are ρ = 999.1 kg/m3 and μ = 1.138x10-3 kg/m.s. The loss coefficient is KL = 0.5 for a sharp-edged entrance. The roughness of cast iron pipes is ε= 0.00026 m.)
The hydroelectric facility that has been proposed will consist of a turbine with anefficiency of 89.2%. The facility will be located at a vertical depth of 14.8 m belowthe riverbed. The river flows with the following properties:o hydraulic diameter of 6.25 mo slope of 0.031o wetted perimeter of 12.2 mo a Chezy coefficient of 4.85 m0-5s1.Thedensity of the river water is 998.2 kg m3, and the acceleration due to gravity is9.81 m s2.Assuming that the turbine operates for 94.0% of the time and one year isapproximately 3.1536 x 107s, calculate:i. the mass flow rate of the river(5 marks)ii. the maximum energy that could be extracted annually from the river flow.
In an hydroelectric plant, 100 m^3/s of water flows from elevation of 120 m to a turbine, where electric power is generated. The overall efficiency of the turbine-generator is 80 percent Disregarding frictional losses in piping. Estimate the electric power output of this plant.
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 5 m long and has a 6-cm diameter, while the second pipe is 5 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate. (The density and dynamic viscosity of water at 15°C are ρ = 999.1 kg/m3 and μ = 1.138x10-3 kg/m.s. The loss coefficient is KL = 0.5 for a sharp-edged entrance. The roughness of cast iron pipes is ε= 0.00026 m.)
In our house water pipe line with diameter of 2.25cm is connected to shower head that has 40 holes. The speed of the water in the pipe line is 1m/sec. i) What is the volume flow rate in the pipe line? ii) At what speed does the water leave one of the holes with diameter 0.001m in the shower head? i) Volume flow rate =_______________ m3/sec ii) Speed of water leaves from holes =_________________ m/sec
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 3-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate.
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 3-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible.Using appropriate software, investigate the effect of the second pipe diameter on the required pumping head to maintain the indicated flow rate. Let the diameter vary from 1 to 10 cm in increments of 1 cm. Tabulate and plot the results
02: Water is to be withdrawn from a 3 m high water reservoir by drilling a 1.5 cm diameter hole at the bottom surface. Disregarding the effect of the kinetic energy correction factor (a = 1). determine the flow rate of water through the hole if (a) the entrance of the hole is well-rounded (K. =0.03) and (b) the entrance is sharp-edged (K, = 0.5).