A 10-kVA, 2200/400 V, single phase distribution transformer has a primary and secondary winding impedances of 5 + j12 and 0.25 + j0.45 ohms, respectively. Calculate the voltage across the secondary terminals at full load, 90 % power factor lagging, when the primary is supplied with 2200 volts?

A 10-kVA, 2200/400 V, single phase distribution transformer has a primary and secondary winding impedances of 5 + j12 and 0.25 + j0.45 ohms, respectively. Calculate the voltage across the secondary terminals at full load, 90 % power factor lagging, when the primary is supplied with 2200 volts?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Related questions

Q: A 10 kVA, 2400/240 V, 60 Hz single phase transformer has Z, = 5.2 + j12.5 ohms and Z2 = 0.06 + j0.12…

A: In this question, We need to calculate the load voltage if Primary voltage and frequency is rated.…

Q: a) What is the minimum required transformer rating in kVA? b) By what percentage could the required…

A: It is given that:

Q: 2. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a per unit…

Q: A 75KVA, 230/115V, 60 Hz transformer was tested with the following result: Short Circuit: 9.5V,…

Q: The open circuit test in a 100 kVA, 2000/200 V, 50 Hz, single phase transformer gives 200 V, 90 A, 5…

Q: An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Culoss…

A: In this question , transformer cu loss and iron loss given..Output KVA given..We have to find out…

Q: A 50 MVA, 11/132 kV three-phase, 50 Hz, generator transformer has guaranteed parameters as, load…

Q: a) What is the complex power drawn and delivered by the transformer? (b) Draw a per-phase equivalent…

Q: A single-phase, 2,959 VA, 2200/220 transformer has the following open circuit and short circuit test…

A: 'Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A 10-kVA, 2000/400-V, single-phase transformer has resistances and leakage reactances as follows :…

A: The information we have : Primary voltage, V1 = 2000 V Secondary voltage, V2 = 400 V So,…

Q: Example 33.3. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a…

A: Given data, Load KVA = 200 kVA Per unit resistance, Rpu=0.02 Per unit reactance Xpu=0.1 Power…

Q: When one transformer is removed from a AA bank of 30 kVA transformer, the capacity of the resulting…

A: we need to find out rating of delta delta transformer when one transformer is removed.

Q: If the turn ratio of a step-down transformer is 10:1 and the series impedance (referred to the…

Q: A 10kVA 2000/400V single phase distribution transformer has a primary and secondary winding…

A: Given: S=10KVA, 2000/400V, Z1=0.5+j10 ohm Z2=0.2+j0.45 ohm pf=0.8 lag ⇒ϕ=36.86°

Q: Q/ An 11,000/230-V, 150-kVA, 50-Hz, 1- phase transformer has a core loss of 1.4 kW and full-load…

A: Given, Full load KVA=150KVA frequency, f=50Hz core loss=1.4kW full load copper loss = 1.6kW

Q: A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is…

A: The efficiency of the transformer is given by the relation, Where, x = percent rated load…

Q: (b) A 50-kVA, 2600/1300-V, single-phase transformer has a core loss of 780 W. The transformer has a…

Q: QI An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load…

A: Given data: Core loss = 1.4 kW Full load Copper loss= 1.6 kW Full load KVA =150 Power factor…

Q: 2) 50 kVA, 2300 V / 230 V transformer draws 750 W power and 0.5 A current at rated idle primary…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: A 10-kVA, 480/120-V conventional transformer is to be reconnected as auto-transformer to supply…

Q: 2. An open delta transformer bank server a balance 3 phase load of 65 kVA at 250 volts and phase…

Q: A transformer was subjected to a no load test with 110 volts impressed at 30 cps. The power input is…

A: When V/F in the transformer is constant then, Eddy current loss is directly proportional to the…

Q: 19.A 25kVA, 2400/240, 60Hz single phase transformer gave the following short circuit test result…

Q: An open delta transformer bank server a balance 3 phase load of 70 kVA at 240 volts and phase angle…

A: The solution is given below.

Q: (a) With neat diagram explain auto transformer and write any two advantages.( (b) A transformer…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Open-circuit test Short-circuit test Voc = 480 V Vsc = 10.0 V loc = 0.41 A Isc = 10.6 A %3D Poc = 38…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: A 5 kVA, 50 Hz single phase transformer has ratio 200/400V. The data taken on the LV side at rated…

Q: A 400/100 V, 5 kVA single-phase two winding transformer is to be used as an auto-transformer to…

A: It is given that: two winding transformer:400/100 Vcosϕ=0.8 laggingη=0.95 %Auto transformer:500/400

Q: Q/ The efficiency of a 400-kVA, single-phase, 60-Hz transformer is 98.77% when delivering full-load…

Q: A 500 kVA, 3-Phase ,11 kV / 430 V distribution transformer with the equivalent percent resistance…

A: Given, Three Phase Transformer Voltage Rating= 11 KV/ 430V Output power= 500 KVA Equivalent…

Q: Two transformers are required for a Scott connection operating from a 440-V, supplying two…

A: To calculate turns ratio, primary and secondary current of both transformer

Q: (b) A transformer takes a current of 0.7A, when its primary is connected to a 225V, 50Hz supply, the…

A: Transformer open circuit test. No load current 0.7A Primary voltage 225V Power =70W

Q: 1. A 11000/230V, 150KVA, 50 Hz single phase transformer has core loss of 1.4kW and full load copper…

Q: 2. (a) A 20 kVA, single phase-phase, 50 Hz, 2200/200 V transformer gave the following test results:…

Q: A 40 kVA, 6,600/250V, 50 Hz transformer is having total reactance of 35 ohms when referred to…

A: Given Data: Rating = 40 kVA R1 = 10 ohm R2 = 0.2 ohm E1 = 6600 V E2 = 250 V

Q: A 120 / 180 Volts Autotransformer draws power a 120 Volts and supplies power to a 2 kW load at 180…

A: Given: The transformer voltage ratio is 120 V/180 V Consider the power supplied to the first load…

Q: A 1-phase transformer, 12 kVA, 600/200V, 50Hz, Short-circuit (high voltage data): 120V, 20A and…

Q: A 230/400 V single-phase transformer absorbs 35 W when its primary winding is connected to a 230 V,…

Q: A 11000/230 V, 150-kVA, 1-phase, 50-Hz transformer has core loss of 1.4 kW and full load copper loss…

A: The solution is given below

Q: . A 15kVA single-phase transformer, for 10000V/440V at no load, has resistances and leakage…

A: In this question, We need to determine the value of the secondary voltage at full load, 0.85 power…

Q: Power transformer A, has Rated power of 150MVA. Line voltage of 330/66 kV Frequency=50Hz Connection…

A: The Figure shows the load sharing in two transformers referred to HV side. V2 = E2A -IAZA…

Q: 2. An open delta transformer bank server a balance 3 phase load of 70 kVA at 240 volts and phase…

A: The solution can be achieved as follows.

Q: A single-phase, 10-kVA, 480/120-V transformer is to be used as an autotransformer tying a 600-V…

A: The base impedance referred to the primary side is determined as: Zb=(480 V)210 KvA=23.04 ohmFor…

Q: ratio

Q: 4. Calculate the full-load primary and secondary currents of a 5-kva 2,400/120-volt transformer.

A: Given power S = 5KVA Primary voltage PV = 2400 Full load primary current = S/PV = 5000/2400 =…

Q: 3. A single-phase 100-kVA, 7200-V/120-V, 60HZ distribution transformer is used as a step down…

A: transformation ratio, primary side impedance, secondary side impedance, primary and secondary side…

Q: Per-Unit System 3) If a 250MUA,11/400 KU, Three-Phase power Transformer has Zpu of 0.05 pu on the…

Q: The primary and secondary windings of a 500-kVA, 11-kV/415-V, single-phase transformer have…

Q: A 5000-KVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent and a…

A: In this question we need to find a equivalent circuit referred to LV side of transformer , voltage…

Q: (b) A 40-kVA, 2600/1300-V, single-phase transformer has a core loss of 620 W. The transformer has a…

A: The solution is given below

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
The leakage reactance of a three-phase, 300-MVA,230Y/23-kV transformer is 0.06 per unit based on its own ratings. The Y winding has a solidly grounded neutral. Draw the per-unit equivalent circuit. Neglect the exciting admittance and assume the American Standard phase shift.