A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg KThe answer (in fundamental SI unit) is? QUESTION 1A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg KThe answer (in fundamental Sl unit) is(type the numeric value only)

Given data :- *the mass of aluminium block (m)=2 Kg *the energy added to the block (Q) = 36KJ Q=…

A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg K The answer (in fundamental SI unit) is?

A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg K The answer (in fundamental SI unit) is?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter4: Temperature Effects On Atom Arrangements And Atom Motion

Section: Chapter Questions

Problem 4.10P

See similar textbooks

Related questions

Q: Calculate the solubility of LaF3 in grams per liter in pure water.

Q: How much bleaching powder is needed to chlorinate 5000l of water whose chlorine demand is 2 mg/l,…

Q: -_ is a carbon- based liquid non-renewable source of energy which is one of the most used today. O…

Q: 2. A system is cooled at constant volume from state 1 to state 2, the internal energy decreasing 88…

A: For a cyclic process net changes in internal energy becomes zero so we can find changes in internal…

Q: Q2/ How much heat does 50g of aluminum give off as it cools from 100c° to 10c°? for aluminum c=88…

Q: Calculate the change in a 5-m long copper wire when its temperature changes by 120 oF.…

A: It is required to determine the change in temperature in oC.

Q: Benzene and Kerosene has a specific weight of 53 and 49 lb/cu.ft. respectively. The weight of…

Q: Which of the following materials has the highest thermal resistivity (R) value? O Steel Concrete…

A: Thermal resistivity is the ability of a material to resist the flow of heat through it. It is the…

Q: A furnace dedicated to paper (assume pure cellulose, C6H10O5) operates with air. How much (g) air is…

A: Write the stoichiometric equation for cellulose pyrolysis as shown below:

Q: One of the following cannot be used as thermal mass. O a. Water O b. Rock O c. Bricks O d. Wood

A: Thermal mass is the ability of a material to absorb and store heat energy and defines a material…

Q: A double-pane glass window consists of two pieces of glass, each having athickness of 8 mm, with a…

A: To determine: Total R-value of window.

Q: A 208 g of C6H6 (78 g/mol.) burns in air according to the equation: CSH6 + O2 C02 +H2O What mass of…

A: Molecular weight of carbon (C) = 12g/mol Molecular weight of hydrogen (H) = 1g/mol Molecular weight…

Q: A 25 gram metal ball heated 200 celcious with 2330 joulse of energy what is the specific heat of the…

A: Given: Weight of metal ball = 25 gm Temperature = 200°C Energy given to metal ball = 2330 J

Q: When 6.3x10'J of heat energy is added to a statue in a heated oven, the statue's temperature rises…

A: Given: The heat energy is 6.3 x 105 J. The initial temperature is 16oC. The final temperature is…

Q: What mass of steam at 100°C must be mixed with 344 g of ice at its melting point, in a thermally…

A: The thermal characteristics of matter are those that cause a substance to conduct heat or that…

Q: A diesel engine required 9,800 kJ of heat to produce 1,800 kJ of power. What is its efficiency?

A: Given data, Power input = 9800 kJ Power output = 1800 kJ

Q: After 2 days, the temperature drops to -10°C. How much does the height change of the À 10 m…

A: Given data : Coefficient of thermal expansion for aluminum (α)=23×10-6 ∘C-1Length of Flagpole…

Q: certain fluid has an enthalpy 1800 KJ/kg and 500 KJ/kg work flow. Find the internal energy.

Q: A refrigerator absorbs 5 kJ of energy from a cold reservoir and rejects 8 kJ to a hot reservoir. (a)…

A: Given: The energy absorbs by the refrigerator is 5 kJ. The energy released by the refrigerator is 8…

Q: 3. A certain copper wire has a resistance of 25 ohms at 10°C. Take the temperature coefficient at…

Q: Stainless steel accessories in cars are usually plated with chromium to give them a shiny surface…

A: As, q = mc tf-t1So, 62.5 = 0.00 5 Kg C 50.8-23⇒ C = 62.50.0005 x 27.8⇒ C = 449.64 J/Kg K

Q: How much bleaching powder is needed to chlorinate 5000l of water whose chlorine demand is 2 mg/l,…

Q: O a. Solar energy O b. Wind energy O c. Mechanical energy O d. Kinetic energy

A: On roof mounting systems are related to solar energy

Q: A piston cylinder device contains 5 kg hydrogen gas. Heat is transferred to the hydrogen as the…

Q: Calculate the dosage of activated carbon to reduce an influent (flowrate = 10 mgd) concentration of…

Q: An aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same…

Q: An insulated Thermos contains 110 cm3 of hot coffee at 83.0°C. You put in a 15.0 g ice cube at its…

Q: Lauren has worker building her house on a hot summer day. She prepares a drink for them by adding a…

Q: What is the minimum amount of ice at 0°C that must be added to the contents of a can of diet cola…

A: The given data is shown below: Latent heat of fusion of ice=333 J/gVolume of can of diet cola=340 ml

Q: The inside temperature of an oven is maintained at 230° C while the kitchen air temperature is 25° C…

A: The measure of hotness or coolness of a body is characterized as temperature. It is expressed in…

Q: A heated metal is placed in cooler surroundings. Its rate of cooling is 2°C per minute when its…

Q: Calculate the specific heat of the material in J/g-deg C if material of 10 kilograms raises by 2 deg…

A: Mass of material = m = 10 kg = 10000 g Rise of temperature = ∆T = 2°C Heat required = H = 2000 J…

Q: If the temperature of the liquid and gas increases by the same amount, what effect does this have on…

A: Viscosity: The property of a fluid that offers resistance for the movement of one layer of fluid on…

Q: An insulated Thermos contains 110 cm³ of hot coffee at 83.0°C. You put in a 15.0 g ice cube at its…

A: To determine the degrees by which the coffee has cooled after adding ice and equilibrium is reached.…

Q: Determine the weight of kerosene in pound.

A: fluid mechanics:

Q: 7. A ceramic insulator is baked at 400°C and cooled in a room in which the temperature is 25°C.…

A: We will use law of cooling formula

Q: a metal is heated up to 500 degree celsius. it is then exposed to a room temperature of 38 degree…

Q: What isthe weight of a 10ft cube tank of oxygen if the oxygen is pressured ti 400 psia, the tank…

A: The given data is as follows: Volume of tank=10ft3 Pressure of oxygen=400 psia Weight of tank=100…

Q: 0/ A fire has been happened near a wall in a building, suppose the heat transfer ation in the wall…

Q: he Bunsen burner in your labs are fueled by natural gas, which is mostly methane, CH4. The…

A: Given, chemical reaction, CH4(g) + 2 O2(g) ➔ CO2(g) + 2 H2O (g) ΔH = –…

Q: List down three to five situations in which buildings, roads or other structures has been built to…

A: Any substance that may be utilised for construction is referred to as a building material. Wood,…

Q: An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling…

A: we knowα=1LdLdTα=18.18148.1942-8.1814100-14α=1.8192×10-5 per °C

Concept explainers

Temperature effects on atom arrangements

Atoms are the smallest units of matter. Atoms can be subdivided into electrons, protons, and several other subatomic particles. Groups or combinations of atoms form molecules that primarily decide the property and behavior of materials. These molecules have the property to attract other molecules based on the valence electrons in the atoms' outermost orbit. An orderly arrangement of molecules is known as crystal structure, which forms the fundamental topic of concern in materials science and engineering. The arrangement of molecules is different for different materials and hence, each material exhibits different lattice arrangements. The lattice arrangements are functions of external loads, deformations, and temperature. On experiencing high temperatures or low temperatures, the behavior of the lattice arrangement of a material change.

Question

A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg K

The answer (in fundamental SI unit) is?

QUESTION 1
A 2.0-kg aluminum block is originally at 10 degrees celcius. If 36 kJ of energy are added to the block, what is its final temperature (in Kelvin)? The specific heat of aluminum is 900 J/kg K
The answer (in fundamental Sl unit) is
(type the numeric value only)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Temperature effects on atom arrangements

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A certain fluid has an enthalpy 1800 KJ/kg and 500 KJ/kg work flow. Find the internal energy.
At the start of compression in an air standard Otto cycle with a compression ratio of 10, air is at 100 kPa and 313.15 K. A heat addition of 2800 kJ/kg is made. Calculate the thermal efficiency. For air, use k=1.4
Calculate the percent volatility of the solids given that an empty container weighs 15.7g. A sample from the aeration tank is put in the container. At temperature 104 degC , the container now weighs 21.2211g. It was further heated in a furnace with a temperature of 540degC and gained a constant weight of 20.5057.
The following information is given for n-pentane at 1 atm:boiling point = 36.20°C ΔHvap (36.20°C) = 357.6 J/g melting point = − 129.7°C ΔHfus (−129.7°C) = 116.7 J/g specific heat gas = 1.650 J/g ⋅ °C specific heat liquid = 2.280 J/g ⋅ °C A 26.10-g sample of liquid n-pentane is initially at −51.40°C. If the sample is heated at constant pressure (P = 1 atm), how many kJ of energy are needed to raise the temperature of the sample to 65.30°C?
A vapor compression refrigeration cycle uses steam as the working fluid. Steamflows steadily with a mass ow rate of 0.5 kg/s. Saturated vapor at 2.0 o C (State 1) enters an uninsulated compressor and it is compressed to 0.35 bar (State 2). Heat transfer at the rate of 105 kJ/s occurs from the compressor to its surroundings and the heat transfer exactly balances the entropy generation rate so that s2 = s1. The boundary and surrounding temperature of the compressor is measured to be 26.67 o C. Steam exits as saturated liquid at 0.34 bar (State 3) from the condenser. Steam leaving the condenser is then throttled in an expansion valve (State 4) before entering a constant pressure evaporator to complete the thermodynamic cycle. (a) Calculate the power (kJ/s) for the compressor. (b) Determine the isentropic efficiency (%) of the compressor. (c) Calculate the entropy generation for the compressor. (d) Find the coefficient of performance of the refrigeration cycle. (e) Show the cycle on T-s…
What is the minimum amount of ice at 0°C that must be added to the contents of a can of diet cola (340mL) to cool it down from 20.5°C to 0°C? Assume that the specific heat and density of the diet cola are the same as for water and that no heat is gained or lost to the surroundings. The latent heat of fusion of ice is 333 J/g.
An aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aAL=23x 10^-6°C and as=12x10^-6° C respectively)
A tank having a volume of 0.85 m3 initially contains water at 260 oF and x = 0.7. Saturated vapor is slowly withdrawn at the top of the tank as energy is transferred by heat to maintain constant pressure. The process continues until the tank is filled with just saturated vapor. Determine the heat transferred in kJ. Show all your calculations.
0.05 kg of steam at 1.5 MPa is contained in a rigid vessel of volume of 0.0076 m^3. A. What is the temperature of the steam? B. If the vessel is cooled, at what temperature will the steam be just dry and saturated? C. Cooling is continued until the pressure in the vessel is 1.1 MPa, calculate the amount of vapor at this point. D. Calculate the amount of heat rejected between the initial and the final state. E. Draw the Ts diagram of the whole process.
A long steel I-beam used in bridge construction has a length of 15.0 m. The beam may be exposed to temperatures as low as −22°C in the winter and as high as 33°C in the summer. What is the difference in length of the beam between these two temperature extremes? (Give the absolute value of the difference. Enter your answer in mm.)
a metal is heated up to 500 degree celsius. it is then exposed to a room temperature of 38 degree celcius. after 2.mins the temperature of the metal becomes 190 degree celsius. when will the temperature be 100 degree celsius? what is the temperature after 4 mins?
Stainless steel accessories in cars are usually plated with chromium to give them a shiny surface and to prevent rusting. When 5.00 g of chromium at 23.00 degrees celsius absorbs 62.5 J of heat, the temperature increases to 50.80 degrees celsius. What is the specific heat of chromium?