A 208N force is applied to a 0.93m long uniform rod (shown in the figure) at the end opposite the pivot point. The angle 01 is equal to 25° and 02 equals 67°.02PivotpointThe magnitude of the torque due to F about some pivot point is determined by T| = rFsin0.Determine the magnitude of the torque, T, on the rod about the pivot point due to F.

A 208N force is applied to a 0.93m long uniform rod (shown in the figure) at the end opposite the pivot point. The angle 01 is equal to 25° and 02 equals 67°. L 02 Pivot point The magnitude of the torque due to F about some pivot point is determined by |7| = rFsin0. Determine the magnitude of the torque, |T|, on the rod about the pivot point due to F.

A 208N force is applied to a 0.93m long uniform rod (shown in the figure) at the end opposite the pivot point. The angle 01 is equal to 25° and 02 equals 67°. L 02 Pivot point The magnitude of the torque due to F about some pivot point is determined by |7| = rFsin0. Determine the magnitude of the torque, |T|, on the rod about the pivot point due to F.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter12: Rotation I: Kinematics And Dynamics

Section: Chapter Questions

Problem 80PQ

See similar textbooks

Similar questions

Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
Consider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75
A disk with a radius of 4.5 m has a 100-N force applied to its outer edge at two different angles (Fig. P12.55). The disk has arotational inertia of 165 kg m2. a. What is the magnitude of the torque applied to the disk incase 1? b. What is the magnitude of the torque applied to the disk incase 2? c. Assuming the force on the disk is constant in each case,what is the magnitude of the angular acceleration applied tothe disk in each case? d. Which case is a more effective way of spinning the disk?Describe which quantity you are using to determine effectiveness and why you chose that quantity. FIGURE P12.55
A rod 7.0 in long is pivoted at a point 2.0 m from the left end. A downward force of 50 N acts at the left end, and a downward force of 200 N acts at the right end. At what distance to the right of the pivot can a third force of 300 N acting upward be placed to produce rotational equilibrium? Sole: Neglect the weight of the rod. (a) 1.0 m (b) 2.0 m (c) 3.0 m (d) 4.0 m (e) 3.5 m
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
What is the torque abot the origin of the force if it is applied at the point whose position is:
Rotational Inertia Problems 5 and 6 are paired. 5. N A system consists of four boxes modeled as particles connected by very lightweight, stiff rods (Fig. P13.5). The system rotates around the z axis, which points out of the page. Each particle has a mass of 5.00 kg. The distances from the z axis to each particle are r1 = 32.0 cm, r2 = 16.0 cm, r3 = 17.0 cm, and r4 = 34.0 cm. Find the rotational inertia of the system around the z axis. 6. N Use the information in Problem 5 to find the rotational inertia of the system around particle 1. FIGURE P13.5 Problems 5 and 6.
Can a set of forces have a net force that is zero and a net torque that is not zero?
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.