A 2,200/250-V transformer takes 8 A at a p.f. of 0.3 on open circuit. a. Find working components of no-load primary current. Note: use four decimal places b. Find magnetising components of no-load primary current. Note: use four decimal places

A 2,200/250-V transformer takes 8 A at a p.f. of 0.3 on open circuit. a. Find working components of no-load primary current. Note: use four decimal places b. Find magnetising components of no-load primary current. Note: use four decimal places

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11P: For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power...

See similar textbooks

Related questions

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: In a transformer MMF remains same i.e, I1N1=I2N2 amd in auto transformer total current is the…

Q: If the open circuit voltage is 239V and the full load voltage is 205V, then the percentage…

A: Voltage Regulation is nothing but ratio of drop in voltage from no load to full load to full load…

Q: Q14 An ideal transformer is rated at 2700/12O 9.6KVA, and has 5o turns on the seund side. Caleulate…

A: Transformer is static device which work on Faraday's Law of electromagnetic induction. The secondary…

Q: A 400-kVA transformer has a primary winding resistance of 192 and a secondary winding resistance of…

A: Transformer is a static electrical device which transfers power from one circuit to another circuit…

Q: A 20 KVA, 480/2000-V, 50 Hz, single-phase transformer is tested with the following results. Find the…

Q: 4.5 +J6 ohms referred to the high-Voltag A 1200/240-V practical transformer has an equivalent…

Q: As given in the figure, the primary side of an ideal transformer is fed from a 400 Volt source with…

Q: The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: In this question, Both transformers are ideal so no losses. We know in transformer I1/I2= N2/N1

Q: Consider the ideal transformer circuit shown below. The turn ratio of the two transformers are given…

A: first we will find imedance seen from the source then current from the source and cureent I2 and I3…

Q: A transformer takes a No load current of 0.64 A and power factor of 0.654 lag, when its primary is…

A: First we will draw phasor diagram , from phasor diagram we will find relation between iron loss…

Q: An ideal transformer has a 150-turn primary and 750-turn secondary. The primary is connected to a…

A: The solution is given below

Q: 23/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent reunt. The results…

Q: From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a…

Q: The single-phase transformer in the following figure has a load voltage Zl of 120 Vrms. If the load…

Q: A single phase transformer takes 10 A on no load at p.f. of 0.2 lagging. The turns ratio is 4: 1…

A: We have a single phase transformer having, No-load current (I) = 10 A Power factor (Cos ϕ0) = 0.2…

Q: Analysis of an Ideal Transformer Circuit The turns ratio of the step-up transformer in Figure 2 is…

Q: Explain the origin of negative voltage regulation in a transformer. Derive the equation of no-load…

A: We will answer both subparts. It is asked to explain the origin of negative voltage regulation in a…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: The single-phase transformer in the following figure has a voltage on the Zl load of 120 Vrms. If…

Q: i If P; be the iron loss and Pc be the cop- per loss on full-load in a transformer, then which of…

A: Given, At full load, Iron loss = Pi Copper loss = Pc Load factor, x = 3/4 (at maximum efficiency)

Q: An ideal transformer has a 150-turn primary and 750-turn secondary. The primary is connected to a…

Q: A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and…

Q: 10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and…

A: In this question we need to find a type of winding connected in LV side.

Q: If the open circuit voltage is 225V and the full load voltage is 214V, then the percentage…

A: Percentage regulation is given by R R = (VOC - VFL ) / VFL VOC = Open circuit voltage VFL =…

Q: For the ideal transformer circuit in the following figure, determine i,(t).

A: Converting the given circuit in 'S' domain

Q: A 400-kVA transformer has a primary winding resistance of 12 and a secondary winding resistance of…

Q: In no-load mode a single phase two windings power transformer draws apparent power S10=100VA at…

Q: Q3/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent circunt. The…

A: given that VOC=230VIOC=0.45APOC=30WPOC =VOCIOCcosϕ∘cosϕ∘=POC VOCIOC=30230×0.45=0.289POC =VOC2RC⇒…

Q: The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230…

Q: 8.(a) A 100 KVA, 50 Hz, 440/11000 V, 1-phase transformer has an efficiency of 98.5% when supplying…

A: Let Pi → Iron losses Pl4→Full load copper losses At full load , 0.8 Power factor efficiency=98.5…

Q: SKVA, 50Hz, single phase transformer, the primary voltage of the transformer is 110V. Reqand X is…

A: Given data, Voltage (Vp)=220 VResistance(Req)=026ΩImpedance(Xeq)=0.4ΩVoltage…

Q: A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000.…

A: a. The turns ratio of the transformer is determined as a=8000230=34.78 The load impedance referred…

Q: Two tests were performed on a 4-kVA , 200/400 V transformer to in order to determine its efficiency.…

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figur Determine the…

A: given transformer and autotransformer

Q: a) Find the equivalent circuit transferred to the high voltage side. b) When the transformer is…

Q: 3 kVA, 50HZ, Single phase transformer, the primary voltage of the transformer is 110V. Req and Xeql…

A: Voltage regulation: It is the change in percentage of output voltage from the no load to full load.…

Q: As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source…

Q: 2. Assuming a center-tapped transformer and T= 0.20msec a Find the turns ratio

Q: A single-phase ideal transformer is rated at 2KVA, 240V/120V. The transformer is supplying rated…

A: A single phase transformer has, Apparent power (S) = 2 kVA Voltage ratio is 240/120 V. Load…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: A, determine V½ l, Z, and the impedance Z',, which is the value of Z, referred to the primary side…

A: Given: N1=1000N2=250V1=1000∠0°I1=5∠30° The relation between voltage and the turns of the transformer…

Q: (a) What will happen if the primary of a transformer is supplied with a DC supply? Show that emf per…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

A: In this question, We need to impedance of the approximately in the primary side and draw the…

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: given transformer and autotransformer

Q: The primary ofa certain transformer takes 1 A at a power factor of 0.4 when connected across a 230…

Q: 6. A 300 kVA, single-phase transformer is designed to have a resistance of 1-5 % and maximum…

A: In this question we need to find a efficiency of transformer at given loading conditions.

Q: A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results…

A: Transformer of 1000 VA,230/115-v Open circuit test(secondary side)Voc=115 vIoc=0.11 APoc=3.9 wShort…

Q: A 7200-240-V, 60-Hz transformer is connected for step-up operation, and a 144/46°-2 load is…

A: Given data, The value of turn ratio is n2n1=7200240. The value of load resistance is R = 144∠46∘ Ω…

Q: F ← N₂ = 40 t ell Denotes iron-core 1,-100 mA For the iron-core transformer of figure. Find the…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

A 2,200/250-V transformer takes 8 A at a p.f. of 0.3 on open circuit.

a. Find working components of no-load primary current. Note: use four decimal places

b. Find magnetising components of no-load primary current. Note: use four decimal places

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An ideal transformer has no real or reactive power loss. (a) True (b) False
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.