A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and leakage- reactance values: R1=40, R2=0.040, X1=120, and X2=0.120. The transformer is operating at 75% of its rated load. If the power factor of the load is 0.866 leading.

A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and leakage- reactance values: R1=40, R2=0.040, X1=120, and X2=0.120. The transformer is operating at 75% of its rated load. If the power factor of the load is 0.866 leading.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.17MCQ

See similar textbooks

Related questions

Q: A commercial 60-Hz, 440/110-volt, 50-kVA power transformer has 600 turns on its high-voltage side.…

Q: (a) A 220 / 400V, 13KVA, 50Hz single phase transformer has at full load, a copper load of 140W. If…

Q: 4.20 A transformer is rated at 2,200:220 volts and 60 cycles per second. If the transformer is used…

Q: A 3300/230 V, 50-kVA, transformer is found to have impedance of 4% and a Cu loss of 1.8% at…

A: Given data, A 3300/230 V, 50-kVA transformer percentage impedance = 4% and Cu loss = 1.8% at…

Q: A l-phase, 10-kVA, 500/250-V, 50-Hz transformer has the following constants: Reactance : primary 0.2…

A: In this question, We need to determine the reading of the instrument for the open circuit test and…

Q: b) A single phase 50 Hz, transformer with turns ratio of 25:1400 has cross sectional area of 110 cm2…

Q: 3. On what particular occasion do we need to use autotransformer? Below is given the diagram of a…

A: transformer which has two electrically secluded windings called: the essential and the optional, an…

Q: A 12-kVA, 240/120-V conventional transformer is to be reconnected as auto-transformer to supply…

A: Connect the auto transformer winding as below

Q: ii) Derive the expression of EMF induced in a Transformer? Why is a transformer rated in KVA?

A: The basic circuit of the transformer is shown below: In the above circuit: Current losses are…

Q: Differentiate an ideal transformer and a practical transformer. Explain the ideal and practical…

A: Before differentiate between ideal and practical transformer let us understand the basics of simple…

Q: TTR 300 , What is the method of connecting the device to the transformer ?

Q: how to do a transformer empty and short-circuit test, what are the most important parameters and how…

Q: The hysteresis loss in a shell type transformer operating at its rated voltage and rated frequency…

A: We need to find out the hysteresis loss when the parameters changed

Q: 3. If a transformer is operated at rated frequency but at voltage higher than the rated value, how…

A: Given that the transformer is operating at a rated frequency but higher voltage The RMS value of…

Q: We have a transformer designed to operate at 60 Hz. The voltage ratings are 4800 V rms and 240 V rms…

A: Given: A transformer is designed to operate at a frequency: f1=60 Hz New frequency is f2=120 Hz…

Q: A 60-Hz single-phase transformer has a turns ratio of 8. The resistances 0.90 2 and 0.05 2 and the…

Q: A 100-kVA, 4800-480-V, 60-Hz, single-phhase distributión has 6 V/turn and an equivalent impedance…

A: Given data: Impedance referred to the high side : 8.48 Ω Output power required: 50 KVA Primary…

Q: QI: Fill in the blanks for the following: 1- The transformer called step-up transformer, when the…

A: Fill in the blanks about Related to transformer and DC machines

Q: Define Mutual Induction and how describe how a transformer operates.

A: Here is the explanation

Q: The magnetic core of a 100 kVA, 60 Hz core-type transformer is wound with 5268 turns on the HV side…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the…

Q: A 10-kVA, 480/120-V conventional transformer is to be reconnected as auto-transformer to supply…

Q: 2-37/13* A 50-kVA, 2300-230-V, 60-Hz transformer supplies a 0.8 lagging power- factor load whose kVA…

A: Solution Given, cos θ = 0.8 core loss= 0.42…

Q: A two-winding transformer is rated at 60-kVA, 240/1200-V, 60-Hz. When operated as a conventional…

A: It s given that: KVA=60V1V2=2401200f=60 Hzcosϕ=0.8 V1V2Auto=2401200

Q: The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding…

Q: Calculate voltage ratio and turn ratio of a 3-phase transformer with data: VIN=6kV, V2N=400V, Dy,

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A single-phase, 100-kVA, 2000-V/200-V, 50-Hz transformer has impedance drop of 10 % and resistance…

A: Transformer is the static device. It transfer the electric energy from one terminal to another…

Q: A 23 KVA, 2300/230 V, 60 Hz step down transformer has the following resistance and leakage reactance…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: A 400/100 V, 5 kVA single-phase two winding transformer is to be used as an auto-transformer to…

A: It is given that: two winding transformer:400/100 Vcosϕ=0.8 laggingη=0.95 %Auto transformer:500/400

Q: The information shown in the table below was obtained when a 60-VA, 120/208 V, 60 Hz transformer was…

A: Given, Power Rating = 60 VA Voltage ratings of the transformer 120/208 V Core loss components from…

Q: A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary…

Q: Illustrate the equivalent circuit of this transformer referred to the high voltage side of the…

Q: The following test data were obtained from short-circuit and open-circuit tests of a 50-kVA,…

A: Given data Apparent power is S = 50 kVA Voltage is V = 600 V frequency is f = 60 Hz a) Calculating…

Q: 3/The core of a 300-kVA, 15000/650 V, 50-Hz, 1-ph, core type transformer has across- section of 30…

A: In the given question we note that The core of = 300 KVA , 1500/ 650 V Cross section area is…

Q: A two-winding transformer is rated at 60-kVA, 240/1200-V, 60-Hz. When operated as a conventional…

Q: Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio…

Q: 1- Why When a transformer is loaded with a constant primary the secondary voltage decreases? 2- What…

A: In this question we will write transformer related problems.... Note :- as per our guideline , I…

Q: a. What does it physically mean if an Ohmmeter measures 'infinite' Ohms between the primary and…

A: a) If the coils of the transformer are not electrically connected, then the resistance between the…

Q: Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio…

Q: ignored in an ideal transformer while considered in a practical 2. Which parameters are transformer…

A: According to guidelines we need to solve only the first question. according to the question we have…

Q: 2. A single-phase, 50-Hz, core-type transformer's no-load voltage ratio is 1,200/440. If the maximum…

A: Since you have asked multiple questions , we will solve the first question for you . If you want any…

Q: • Q1: During the separation of transformer core losses experiment: 1. Why should always keep the…

Q: Why the terms Rm and Xm significant when the transformer is loaded?

A: At under rated load condition the applied voltage is always constant, there is only changing…

Q: A 5000-VA, 480/120-V conventional two-winding transformer is to be used to supply power from a 600-V…

Q: During short-circuit test of a transformer, which winding must be short-circuited? Why?

Q: QS/A single phase, 50-Hz transformer has 80 turns on the primary winding and 400 turns on the…

Q: Explain the working principle of a transformer.

Q: A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and leakage-…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

100%

A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and leakage-
reactance values: R1=40, R2=0.040, X1=120, and X2-0.120. The transformer is operating at 75%
of its rated load. If the power factor of the load is 0.866 leading.
Determine the efficiency of the transformer.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
What is the purpose of a transformer? Draw the symbols for a transformer.
Why is it important to reduce the moisture within a transformer to acceptable levels during transformer installation?
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.