Consider a series of pipes as shown in the figure below that carries a discharge of 100 of water. Which of the following is TRUE? 100 kPa Pipe B 200 kPa Pipe A 150 mm dia a. The flow is from A to B since Pipe A has higher pressure. b. The flow is from A to B since Pipe A has a higher piezometric head. c. The flow is from B to A since Pipe B has higher elevation. d. The flow is from B to A since Pipe A has a higher total head. e. The flow is from B to A since Pipe B has higher flow velocity. When writing the energy equation, which of the following terms is NOT ZERO? a. The pressure head at a reservoir b. The pressure head at a free jet c. The velocity head at a free jet d. The velocity head at a reservoir 100 mm dia 5m

Consider a series of pipes as shown in the figure below that carries a discharge of 100 of water. Which of the following is TRUE? 100 kPa Pipe B 200 kPa Pipe A 150 mm dia a. The flow is from A to B since Pipe A has higher pressure. b. The flow is from A to B since Pipe A has a higher piezometric head. c. The flow is from B to A since Pipe B has higher elevation. d. The flow is from B to A since Pipe A has a higher total head. e. The flow is from B to A since Pipe B has higher flow velocity. When writing the energy equation, which of the following terms is NOT ZERO? a. The pressure head at a reservoir b. The pressure head at a free jet c. The velocity head at a free jet d. The velocity head at a reservoir 100 mm dia 5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
A centrifugal pump is used to pump water through horizontal distance of 150 meters and then raised to an overhead tank 20 meters above. The pipe is smooth with inside diameter of 50 millimeter. The pump head (meter of water) that will be generated at its exit to deliver water at a flow rate of 0.001 cubic meter per second is Blank 1 meter of water. Use fanning friction factor = 0.0062 Express your answers in whole siginificant figure without decimal value and without unit
CHOICES FOR PIPE 3: A. 733, B.373, C. 133, D. 311 Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes. AND PIPE 2
A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute delivers water at a temperature of 150oF. If the slip is 7%, determine the discharge in a. discharge in Answer : __________________ lb/hrb. discharge in Answer : __________________ gpm
A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice pointing upstream and other perpendicular to it. The mean velocity in the pipe is 0.80 of the central velocity Find the discharge through the pipe if the pressure difference between the two orifices 60 mm of water. Take the co-efficient of pitot tube as C, = 0.98.
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
a) Two pipes have a length ? each. One of them has a diameter D, and the other a diameter d.if the pipes are arranged in parallel, the loss of head when a total quantity of water Q flows through them is h, but, if the pipes are arranged in series and the same quantity Q flows through them, the loss of head is H. If ?=?/2, find the ratio of H to h, neglecting secondary losses and assuming the pipe coefficient f has a constant value. b) A pipeline of 0.6m diameter is 1.5km long.To increase the discharge, another line of the same diameter is introduced parallel to the first in the second half of the length.Neglecting minor losses, find the increase in discharge if 4f = 0.04. The head at inlet is 300mm. c) Determine the difference in the elevations between the water surfaces in the two tanks which are connected by a horizontal pipe of diameter 300 mm and a length of 400 mm. The rate of flow of water through the pipe is 300 litres/s. Consider all losses and takef=0.008. d) Water at 20°C is…
Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? Indicate the Free Body Diagram
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
1. How does the manometer reading of the Orifice Meter apparatus affect its discharge? If the flowrate passing through the apparatus is increased, what will happen to the corresponding theoretical discharge?