A pipe has a diameter of 100 mm at section AA and a diameter of 50 mm at section BB. The velocity of an incompressible fluid is 0.3 m/s at section AA. What is the flow velocity at section BB? O 0.95 m/s O 3.5 m/s 2.1 m/s O 1.2 m/s

A pipe has a diameter of 100 mm at section AA and a diameter of 50 mm at section BB. The velocity of an incompressible fluid is 0.3 m/s at section AA. What is the flow velocity at section BB? O 0.95 m/s O 3.5 m/s 2.1 m/s O 1.2 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What regime favors heat transfer and why? Laminar, Turbulent or Transitional

A: Heat transfer is basically a process in which the molecules are moved from their initial position in…

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A: given; radius of propeller shaft(rB)=1.2 in…

Q: Why do most materials exhibit an increase in dimensions when heated?

A: Thermal Expansion of material : When the material heated it gets expands is called as thermal…

Q: Ex. For the system shown in the Fig bellow write equation of motoin and Find the naturad frequencyp…

Q: 4. A plate of 270 mm wide and 25 mm thick from carbon steel. A two-high rolling mill is used to…

Q: The free-body diagram for the engine is also shown. Which of the following are true? (Select all…

A: Introduction: Free-body diagrams are used to depict the magnitude and direction of all forces…

Q: Example 5.2.3: Using the Lagrangian method, derive the equations of motion for the…

Q: T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm…

Q: A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm…

A: We know that a cylinder is made up of an outer tube with internal and external diameters of 16 cm…

Q: A one-ton car is initially travelling at 10 kph when it combusts 50 grams of fuel with calorific…

A: Given data v1=10 kphCV=15000 kJm=1000 kg Here, m is the mass of the car and CV is the calorific…

Q: Q10: Windmills slow the air and cause it to fill a larger channel as it passes through the blades.…

A: In the fluid mechanics the ratio between the mass of the fluid to the volume of that fluid is known…

Q: A tensile specimen of the metal of 100 mm is length stretched to a length = of 157 mm during the…

Q: Convert the reading of pressure to kpa.

A: Given; Convert 4.2 bar into KPa ?

Q: The following creep data were taken on an aluminum alloy at 480 C (900 F) and a constant stress of…

A: Enter the given values in Excel: To find: (a) Steady-state or minimum creep rate. (b) time of…

Q: the temperature T3 in K is nearly equal to

Q: Label the following diagram of a fluid dispensing system using the provided labels Volume Request…

A: Introduction: Fluid dispensing system/equipments: Any machine that distributes, mixes and…

Q: A four – cylinder, 2.5 liter, SI automobile engine operates at WOT on a four- stroke air – standard…

A: given; volume(V1)=2.5liter =2.5*10-3m3compression ratio(r)=8.6initial…

Q: 2/72 With what minimum horizontal velocity u can a boy throw a rock at A and have it just clear the…

A: When an object is launched obliquely near the earth's surface, it follows a curving path with…

Q: A reciprocating compressor cómpresses 1 m³/min of gas from 1 bar to 5 bar. The clearance is 8% and…

A: Given data as per the question Initial pressure = 1 bar Initial volume 1 m3/min Final pressure = 5…

Q: Q. Define coefficient of discharge and write equation for actual discharge.

A: Coefficient of dischargeCoefficient of discharge is defined as the ratio of the actual flow…

Q: A reciprocating compressor cómpresses 1 m³/min of gas from 1 bar to 5 bar. The clearance is 8% and…

Q: The capitalized cost of a piece of equipment was found to be 145,000. The rate of interest used in…

Q: Determine the distance "a" for which the largest absolute value of the bending moment of the beam is…

A: First calculate the reactions. Then draw the bending moment diagram

Q: 2. A tensile specimen of the metal of 100 mm is length stretched to a length = of 157 mm during the…

Q: 3. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and 37.50308414 atm…

Q: A 10-inch waterwheel were spinning by the weight of flowing water at one liter per second. If the…

Q: 3- Compute minimum force F which barely prevent block A from sliding. Block B is connected to a…

Q: Q4-A square threaded screw is required to work against an axial force of 6000N and has following…

A: Given Force, F = 6000 N Diameter, d = 32 mm Pitch, p = 4 mm Find Torque, T

Q: A Kaplan turbine of 100 B.H.P. is working under a head of 5 in and running at 210 R.P.M. The…

Q: Example For the system shown, the equations of motion are given by m₁*₁ + cx₁ + kx₁ Cx₂ = 0 m₂x₂ +…

A: Given : To find : State space model

Q: Two components of a steam engine are shown in the figure below. The turbine is adiabatic. a.…

Q: Situation 9 - Refer to Figure CO23.52. The columns loads of the combined footing are P₁ = 1200 kN…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Traffic travels at 65 mi/hr around a banked highway curve with a radius of 3000 ft. What banking…

A: The banking angle required such that friction will not be required to resist the centrifugal force…

Q: The efficiencies of aircraft can be very important indicators for meeting emission standards. Often…

A: Given Calorific value, LCV = 43.15 MJ/kg Fuel consumption, s = 0.06 kg/hr Mass of fuel,…

Q: Q2/ Determine the centroid coordinates of the shaded area shown in figure 2.All dimensions in…

Q: A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm…

A: We know that a cylinder is made up of an inner tube with an internal and external diameter of 8 cm…

Q: Determine the force in members ab,dh,dg, eg, hi,hj, & hk of truss shown in figure !

Q: A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm…

A: Given data: Cycle : Reheat steam cycleThrottle Pressure = 13580 kPaReheat Pressure = 37.50308414…

Q: Air is drawn in a gas turbine unit at 15°C and 1.01 bar and pressure ratio is 7: 1. The compressor…

A: Given that, Temperature of air, T=17 °C,Pressure of air, P=1.01 bar,Pressure ratio, rp=8:1Isentropic…

Q: What is the reading below, in mm

Q: A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick,…

A: In thermodynamics the transfer of the molecules from the one high temperature body to the lower…

Q: Label the following diagram of a fluid dispensing system using the provided labels • Volume Request…

A: Introduction: Fluid dispensing system equipmens: Fluid dispensing equipment includes any machine…

Q: A centrifugal pump delivers water at a rate of 0.03 m³/sec to a height of 18 meters through a pipe…

A: Given that, Q=30 litres/s=301000 m3/s=0.03 m3/sH=18 m, L=90 mPipe diameter, d=100 mm=0.1 mηo=75…

Q: a 20 mm diameter steel pipe is used to drain and oil tank (SG-0.88) as shown. The total head loss is…

Q: The efficiencies of aircraft can be very important indicators for meeting emission standards. Often…

A: Given Calorific value, LCV = 43.15 MJ/kg Fuel consumption, s = 0.06 kg/hr Mass of fuel,…

Q: A rod of negligible mass is attached to a wall by a frictionless pivot and supported by two springs…

Q: Convert the reading of pressure to kpa.

A: Given data; Borometer reads =760 mm of Hg Convert 80 cm of Hg into kpa ?

Q: H.W₂ Sow at • A Power transistor for which TJmax = 180°c Can dissipat- a case temperature of so°c.…

Q: A Borda's mouthpiece 150 mm in diameter discharges water under a head of 3 m. Determine the…

Q: What is truss

A: This question is based on the concept of trust in mechanical engineering.

Question

Please answer quickly thank you (3)

A pipe has a diameter of 100 mm at
section AA and a diameter of 50 mm
at section BB. The velocity of an
incompressible fluid is 0.3 m/s at
section AA. What is the flow velocity
at section BB?
O 0.95 m/s
O 3.5 m/s
O2.1 m/s
O 1.2 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water, assumed incompressible, flows steadily throughthe round pipe in Fig. The entrance velocity is constant,u = U 0 , and the exit velocity approximates turbulentfl ow, u = u max (1 - r / R ) 1/7 . Determine the ratio U 0 / u max forthis flow.
[CE Hydraulics] 5. For the case of turbulent flow in rough pipes, does the friction factor depend on the Reynolds number? Why?
If the inner diameter of the penstock that deliver water form the dam to the hydroelectricpower plantis 90 cm and the water flows inside itat a rate of 10 L/s. (?=0.0131?????)a.Define the type of flowinside the penstockusing Reynolds numberequation.b.Explain the significance of the information we get from Reynolds number equation.
Water at 25 deg C (998 kg/m 3 ) flows at 10 m 3 /s through a straight pipe of an ID of 1.38 m to 2 m-ID. Consider the level of the entrance and terminal bottom walls of the pipe equal, neglecting the effects of potential energy. In addition, the shaft work is zero. What is the Reynold's number. What kind of flow regime?
A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at 20 C. a. What is the velocity of the water (average) in the pipe? b. What is the Reynolds number value? c. Is the flow laminar or turbulent?
At the end of the summer, a swimming pool is being drained through a very long,small-diameter hose. The hose is smooth, of inner diameter D = 6.0 cm,and of length L = 65 m. The initial height difference from the pool surface to theoutlet of the hose is H = 2.20 m. Calculate the volume flow rate in litres per minute(LPM) at the start of draining.
Calculate the head loss due to friction in a pipe of diameter 25 cm and length 60 m, through whichwater is flowing at a velocity of 2 m/s. (a.) Darcy formula (b.) Chezy’s formula for which C = 60.
For fully developed laminar pipe flow in a circular pipe, the velocity profile is given by u(r)= 2(1- r2 / R2) in m/s. Where R is the inner radius of the pipe. Assuming that the pipe diameter is 4 cm. find the maximum and average velocities in the pipe as well as the volume flow rate.
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.
Throughof the system that showsof the figure circlesa flow rate of 100L/slight oil(s=0.72), which ispowered by apump it upsupplies apower of 5.0 kW andworks with a85% efficiency.determine the timegauge mmdifferential
Water at 10°C flows from a large reservoir to a smaller one through a 5-cm-diameter cast iron piping system, as shown in Fig. Determine the elevation z1 for a flow rate of 6 L/s.
Determine (a) the head loss, (b) the pressure drop, and (c) the pumping power for water flowing steadily at 40°F (ρ=62.42 lbm/ft3 and μ=1.038x10-3 lbm/ft-s) through a 0.15-in diameter, 45-ft-long horizontal pipe at an average velocity of 2.5 ft/s. Round off your answers to three (3) decimal places.