A 300 m ning distnibutor has loads as shown in Fig. 13.45 where distances are in metres. The resis- tance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. [V3=2369 V ; Vc= 235-97 V ; V½= 237-45 V] 240 V 30 A 10 A 70 OA A 60 100 A B 230 V +20 A 90 80 B. 70 A 10 A Fir. 13.45 Fir. 1346

A 300 m ning distnibutor has loads as shown in Fig. 13.45 where distances are in metres. The resis- tance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. [V3=2369 V ; Vc= 235-97 V ; V½= 237-45 V] 240 V 30 A 10 A 70 OA A 60 100 A B 230 V +20 A 90 80 B. 70 A 10 A Fir. 13.45 Fir. 1346

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please Solve ASPS. A 100 kVA, 2000/400 V, 50 Hz, single phase shell type transformer has sandwitch coils. There are two full HIV coils, one full LV coil and two half LV colls. Calculate the value of leakage reactance referred to HV side if the other data given is, depth of HV coil = 4 cm depth of LV coil = 3.6 cm depth of duct between IIV and LV= 1.6 cm width of winding 12 cm length of mean turns = 150 cm HV winding turns = 200 Also calculate the per unit reactance.
An Electrical engineer is asked by a client to prepare a technical specification on specific items connected with a project. Hence, the engineer is requested to prepare the technical specification of the following: PROJECT: A Subdivision Development Lot AREA; 2 Hectares LOCATION: Brgy. Kanlurang Mayao, Lucna City Technical specification of fuse cutout Technical specification of transformer
Given a 115kV/13.2kV distribution transformer rated at 30MVA with an 8% nameplate impedance what is the full Load current in amps
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A three-phase, three-wire, 500-V, 60-Hz source supplies a three-phase induction motor, a wye-connected capacitor bank that draws 2 KVAr per phase, and a balanced three-phase heater that draws a total of 10 kW. The induction motor is operating at its rated 75 Hp and has an efficiency and power factor of 90.5 and 89.5 percent, respectively. Determine the system KVA. 78.12 75.98 24.81 83.17
Q13) An ideal transformer connected to a 240V mains, supplies a 12V, 150W lamp. Calculate the Transformer turns ratio. a. 45 b. 0.05 c. 50 d. 5
single coil 600 turns instrument transformer, operating in the step-down mode with a 40 percent tap, supplies a 5 kVA, 0.88 power factor inductive load. The input to the transformer is 3.3 kV, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (0) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp); (iv) Transformed current (in Amp); (v) Apparent power conducted(in kVA)and (vi) Apparent power transformed"
"A single coil 800 turns instrument transformer, operating in the step-downs mode with a 25 percent tap, supplies a 10 kVA, 0.80 power factor lagging load. The input to the transformer is 6600 V, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (i) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp); (iv) Transformed current (in Amp); (v) Apparent power conducted(in kVA)and (vi) Apparent power transformed"
The impedance value for a network containing the utility and a transformer is Select one: None of these Zt=√(〖((Ztranformer)〗2+〖((Zutility)〗2 Zt=Ztransformer+Zutility Zt=√(〖((Xtranformer+Xutility)〗2+〖((Rtranformer+Rutility)〗2
A network is composed of the utility having Ssc=500MVA, and an 800KVA transformer, rated at 20KV/410V (no load), whose voltage impedance is 5%, and whose load losses are 5400watts. the short circuit at the secondary of the transformer using the impedance method is: Select one: a)30.5KA b)None of these c)45.8KA d)21.83KA
Calculate the mesh currents in the circuit of Fig. 13.11.
A choke coil of resistance 8 ohm and inductance 0.15 H is connected in series with a capacitor of capacitance 125 ?? across a 230-V, 50- Hz supply. Calculate: (a) the inductive reactance, (b) capacitive reactance, (c) impedance, (d) current, (e) voltage across the coil and the capacitor, respectively. (f) phase difference between the current and the supply voltage.
1) A 600 V source feeds a 480 V load with a transformer Conventional 5000 VA, 480/120 V. Consider the ideal transformer. a) Calculate the apparent nominal power of the transformer in the connection as Autotransformer. b) Calculate the currents on the high voltage side and on the low voltage side in these conditions. c) Calculate the current in the common coil in the connection as Autotransformer.