single coil 600 turns instrument transformer, operating in the step-down mode with a 40 percent tap, supplies a 5 kVA, 0.88 power factor inductive load. The input to the transformer is 3.3 kV, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (0) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp);

single coil 600 turns instrument transformer, operating in the step-down mode with a 40 percent tap, supplies a 5 kVA, 0.88 power factor inductive load. The input to the transformer is 3.3 kV, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (0) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp);

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8 kVA, 0.85 lagging power factor load. The input to the transformer is 2400 V, 60 Hz. Neglect the small losses and leakage effects. What will be the apparent power(in kVA) conducted and transformed respectively?
A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming an ideal transformer, finda. The numbers of high-side turns Nh and low-sideturns Nl .b. The rated current of the high-voltage side Ih.c. The transformer ratio when the device is used as astep-up transformer.
A 240-kVA, 480/4800-V, step-up transformer has the following constants: Rs = 2.5 Ω, Xs = j5.75 Ω, Rp = 25 mΩ, Xp = j57.5 mΩ. The core-loss resistance and the magnetising reactance on the high-voltage side are 18 kΩ and j12 kΩ, respectively. The transformer is operating at 50% of its rated load. If the load is purely resistive, determine the percent power efficiency of the transformer
A 230/400 V single-phase transformer absorbs 35 W when its primary winding is connected to a 230 V, 50 Hz supply, the secondary being on open circuit. When the primary is short-circuited and a 10 V, 50 Hz supply is connected to the secondary winding, the power absorbed is 48 W when the current has the full-load value of 15 A. Estimate the per unit efficiency of the transformer at half load, 0.8 power-factor lagging.
A 150-kVA single-phase transformer has a core loss of 1.5 kW and a full-load Cu loss of 2 kW. Calculate the efficiency of the transformer (a) at full-load, 0.8 p.f. lagging (b) at one-half full-load unity p.f. Determine also the secondary current at which the efficiency is maximum if the secondary voltage is maintained at its rated value of 240 V
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary resistances of 0.2ohm and 0.05 ohm respectively, the corresponding leakage reactances being 0.3 ohm and 0.01 ohm respectively.1. Calculate the equivalent resistance, reactance and impedance referred to the low-voltage (secondary) side.2. Find the high (primary) voltage when the transformer is supplying full-load current at rated secondary voltage at 0.8 powerfactor lagging.3. Draw the phasor diagram showing your answer in 2.
A 100-kVA, 2500/125-V, 50-Hz, step-downtransformer has the following parameters: R1=1.5Ω, X1= 2.8Ω, R2 = 15mΩ, X2 =20mΩ, Rc1 =3kΩ, Xm1 = 5kΩ The transformer delivers 85% of the rated load ata terminal voltage of 115 V and a power factor of0.866 lagging. Determine (a) the efficiency, and(b) the voltage regulation. Draw the phasordiagram of the transformer. Use the approximate equivalent circuit referredto the secondary side.
A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.
The equivalent parameters of a 150kVA, 2400V/240V transformer, are R1=0.2Ω, R2=2mΩ, X1=0.45Ω, X2=4.5mΩ, Rc=10kΩ, and Xm=1.55kΩ. The transformer is operating at rated load and rated voltage with 0.8 lagging power factor. Using the approximate equivalent circuit referred to the primary side, determine: (i) the voltage regulation (ii) the transformer power loss and efficiency Please refer to the answer
Primary side-reduced equivalent circuit parameters of a 25 KVA, 50 Hz, 4000/400 Volt transformer R1 = 32 Ω, X1 = 45 Ω, Rc = 250000 Ω, R2 '= 66.14 Ω, X2' = 79.34 Ω, Xm It is given as = 30000 Ω. Since the secondary of the transformer is fed at a full load rated voltage with an advanced power factor of 0.9, for these operating conditions; a) Calculate the primary voltage using the T equivalent circuit. (Only the amplitude of the voltage and the phase value will not be entered.) b) Calculate the efficiency of the transformer. c )Calculate the voltage regulation of the transformer.
A 120:480-V, 10-kVA step-up two-winding transformer is to be used as an autotransformer to supply a 120-V circuit from a 600-V source (a step-down autotransformer). When it is tested as a two-winding transformer at rated load, unity power factor, its efficiency is 97.9 %. 1.Show the connection diagram of the transformer converted as an autotransformer and identify which is the series winding Nse and the common winding Nc.