A single coil 800 turns instrument transformer, operating in the step-downs mode with a 25 percent tap, supplies a 10 kVA, 0.80 power factor lagging load. The input to the transformer is 6600 V, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (i) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp); (iv) Transformed current (in Amp); (v) Apparent power conducted(in kVA)and (vi) Apparent power transformed"

A single coil 800 turns instrument transformer, operating in the step-downs mode with a 25 percent tap, supplies a 10 kVA, 0.80 power factor lagging load. The input to the transformer is 6600 V, 50 Hz. Assume that leakage effects and minor losses in transformer are negligible. Determine the following : (i) Turn ratio; (ii) Load current(in Amp); (iii) Incoming line current(in Amp); (iv) Transformed current (in Amp); (v) Apparent power conducted(in kVA)and (vi) Apparent power transformed"

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8 kVA, 0.85 lagging power factor load. The input to the transformer is 2400 V, 60 Hz. Neglect the small losses and leakage effects. What will be the apparent power(in kVA) conducted and transformed respectively?
A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming an ideal transformer, finda. The numbers of high-side turns Nh and low-sideturns Nl .b. The rated current of the high-voltage side Ih.c. The transformer ratio when the device is used as astep-up transformer.
A transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage of a distribution system. The low tension voltage is to kept constant at 220V. (a) What load Impedance connected to the low-tension side will be loading the transformer fully at 0.8 power factor (lag) ? (b) What is the value of this impedance referred to the high tension side?
A 230/400 V single-phase transformer absorbs 35 W when its primary winding is connected to a 230 V, 50 Hz supply, the secondary being on open circuit. When the primary is short-circuited and a 10 V, 50 Hz supply is connected to the secondary winding, the power absorbed is 48 W when the current has the full-load value of 15 A. Estimate the per unit efficiency of the transformer at half load, 0.8 power-factor lagging.
A 150-kVA single-phase transformer has a core loss of 1.5 kW and a full-load Cu loss of 2 kW. Calculate the efficiency of the transformer (a) at full-load, 0.8 p.f. lagging (b) at one-half full-load unity p.f. Determine also the secondary current at which the efficiency is maximum if the secondary voltage is maintained at its rated value of 240 V
A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.
A single-phase l0-kVA, 480/1120 -V transformer is to be used as an auto transformer tying a 600V distribution line to a 480-V load. When it is tested as a conventional transformer, the following values are measured on the primary (480-V) side of the transformer: a. Find the per-unit equivalent circuit of this transformer when it is connected in the conventional manner. b. What is the efficiency of the transformer at rated conditions and unity power factor? c. What is the voltage regulation at those conditions?
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary resistances of 0.2ohm and 0.05 ohm respectively, the corresponding leakage reactances being 0.3 ohm and 0.01 ohm respectively.1. Calculate the equivalent resistance, reactance and impedance referred to the low-voltage (secondary) side.2. Find the high (primary) voltage when the transformer is supplying full-load current at rated secondary voltage at 0.8 powerfactor lagging.3. Draw the phasor diagram showing your answer in 2.
1) A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following: (a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.
A 100-kVA, 2500/125-V, 50-Hz, step-downtransformer has the following parameters: R1=1.5Ω, X1= 2.8Ω, R2 = 15mΩ, X2 =20mΩ, Rc1 =3kΩ, Xm1 = 5kΩ The transformer delivers 85% of the rated load ata terminal voltage of 115 V and a power factor of0.866 lagging. Determine (a) the efficiency, and(b) the voltage regulation. Draw the phasordiagram of the transformer. Use the approximate equivalent circuit referredto the secondary side.