A 30cm-by-30cm flat plate is being pulled at 5.2 m/s horizontally through a 3.6 mm thick oil layer between two plates, one being stationary and the other moving at a constant velocity = 2.2 m/s, The dynamic velocity of the oil layer is 0.027 Pa∙s. How would I plot the velocity profile and find the location where the oil velocity = 0?

A 30cm-by-30cm flat plate is being pulled at 5.2 m/s horizontally through a 3.6 mm thick oil layer between two plates, one being stationary and the other moving at a constant velocity = 2.2 m/s, The dynamic velocity of the oil layer is 0.027 Pa∙s. How would I plot the velocity profile and find the location where the oil velocity = 0?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.36P

See similar textbooks

Similar questions

Estimate the entrance length for motor oil for the following two cases: (a) SAE10W-30 oil flowing through a 0.1-in diameter tube in an engine at 0.01 gal/s and (b) SAE 10W-30 oil flowing through a 6-in diameter pipe at 500 gal/s.
A local ventilation system (a hood and duct system) is used to remove air and contaminants from a pharmaceutical lab (Fig. 1). The inner diameter (ID) of the duct is 129 mm, its average roughness is 0.15 mm, and its total length is L = 24.5 m. There are three elbows along the duct, each with a minor loss coefficient of 0.21. Literature from the hood manufacturer lists the hood entry loss coefficient as 3.3 based on duct velocity. When the damper is fully open, its loss coefficient is 1.8. The minor loss coefficient through the 90° tee is 0.36. Finally, a one-way valve is installed to prevent contaminants from a second hood from flowing “backward” into the room. The minor loss coefficient of the (open) one-way valve is 6.6. The performance data of the fan fit a parabolic curve of the form Havailable = H0 - aV2, where shutoff head H0 = 60.0 mm of water column, coefficient a = 2.50 x 10-7 mm of water column per (Lpm)2 ,available head Havailable is in units of mm of water column, and…
Equation 6.16: εT = ln(li / l0)
fluid mechanics In order to prevent flooding in irrigation areas and to direct the water back to the river or waterbed, the flat cover system given below is preferred. The weight of the cover is 871 kg. The square section cover is hinged 1m above the center of the cover (a = 0.25 m) and b = 1.5 m. The cover has a vertical angle of 40 What should be the maximum water head (h) according to the instructions so that the cover does not open? (psu=1000kg/m3)
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where the shutoff head H0 = 125 ft of water column, coefficient a = 2.50 ft/(gpm)2 , available pump head Havailable is in units of feet of water column, and capacity V. is in units of gallons per minute (gpm). Estimate the capacity delivered by the pump
Calculated f) as 4690 l/s, g) as 1.29m/s and h) as 293.89 bar. How to calculate i) average velocity of flow at cross section 4
Describe in detail the three types of flexible hose assemblies, and how they are normally classified? (FAA-H-8083-30A pg.9-18)
Thermal power plant burns 200 kilolitres diesel per day. In ideal conditions, burning of 1.0 kg diesel requires 14.2 kg of air. Parallel plate type ESP is installed to remove the particulates. If the height of channels is 4.5 m and the spacing between electrodes is 0.25 m, calculate: (i) Flue gas discharge in m3 per day (ii) The number of channels required (iii) Number of discharge electrodes provided (iv) Number of chambers required
Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine. The dimensions and values are given. One of the steps is not required to find the required length of the HX, if the oil leaves at 60 C? Oil and water inlet temperatures are 100 and 30 C, respectively. a) Log mean temperature difference b) Thermal entry length to validate the steps c) None of the above d) Reynolds number, Prandtl number and Nusselt number e) Overall heat transfer coefficient
Which of the ff equations is true regarding the pipe network ? i.Qin = QB + QA ii.QA + QD + QF = 0 iii.QD + QE = QG iv. Qin + Qout = 0
Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine. The dimensions and values are given. One of the steps is not required to find the required length of the HX, if the oil leaves at 60 C? Oil and water inlet temperatures are 100 and 30 C, respectively. Log mean temperature difference Overall heat transfer coefficient Thermal entry length to validate the steps None of the above Reynolds number, Prandtl number and Nusselt number
Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine. The dimensions and values are given. One of the steps is not required to find the required length of the HX, if the oil leaves at 60 C? Oil and water inlet temperatures are 100 and 30 C, respectively. Log mean temperature difference Thermal entry length to validate the steps Overall heat transfer coefficient Reynolds number, Prandtl number and Nusselt number None of the given