00%240y4%23V)dyis the final temperature of the part (c of Al = 0.900 J/g K)?A 359-g aluminum engine part at an initial temperature of 24.60°C absorbs 66.2 kJ of heat. What

Formula used:- Q = mc∆T Where Q = Heat absorbed m = mass c = specific heat capacity ∆T =…

Answered: A 359-g aluminum engine part at an…

A 359-g aluminum engine part at an initial temperature of 24.60°C absorbs 66.2 kJ of heat. What is the final temperature of the part (c of Al = 0.900 J/g-K)? °C

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter12: Thermodynamic Processes And Thermochemistry

Section: Chapter Questions

Problem 14P

See similar textbooks

Related questions

Q: TUS V Complete the table below. Be sure each of your answer entries has the correct number of signif...

Q: 4) Choose how many “occupied MOs" can occur for the conjugated n-system of B-carotene and LED compou...

A: These type of questions are based on pericyclic reactions let us discuss one by one.

Q: Explain why fats contain more kcal than carbohydrates. Please include information about the oxidatio...

A: Fats have more energy than carbohydrates and proteins. This is because of the oxidation rate of the ...

Q: mis energy diagram shows the allowed energy levels of an electron in a certain atom or molecule: A B...

A: The lowest energy State is the ground state. All the other energy states other than ground state are...

Q: Name the following compounds and show how you numbered each carbon atoms. note: I need the answer im...

Q: One dose of an antacid contains 860. mg each of Mg(OH)2 and Al(OH)3. How many moles of each compou...

A: Given:- One dose of an antacid contains 860. mg each of Mg(OH)2 and. Al(OH)3. To find:- How many...

Q: Ammonium hydrogen sulfide decomposes according to the following reaction, for which Kp = 0.11 at 250...

A: Given, NH4HS(s) ⇌ H2S(g) + NH3(g) Equilibrium constant (Kp) = 0.11 Temperature (T) = 250°C mass of N...

Q: 1. Calculate the heat evolved when 13.56g of oxygen gas (O2) is used to burn white phosphorus at st...

A: 1) Given, P4(s) + 5O2(g) → P4O10(s), ΔH = -3013 kJ/mol ∆H is in negative (-) which indicate the rele...

Q: Balance the chemical equation below using the smallest possible whole number stoichiometric coeffici...

A: Given :

Q: MASS PERCENT Complete the table: Mass Solute Mass Solvent Mass Solution Mass Percent 15.5 g 238.1 g ...

Q: Chapter 4 Calculations: Molarity and Solution Stoichiometry Question 7 of 15 > -/1 View Policies Cur...

Q: Calculate pF at the equivalence point of a titration of 20.00 mL of 0.01039 M La (NO3)3 with 0.00633...

A: Here pF can be determined from the Ksp value of LaF3 formed at equivalent point. Data Ksp LaF3 = 2.7...

Q: Sodium carbonate is a reagent that may be used to standardize acids in the same way that you have us...

A: Given - Weight of Na2CO3 = 0.498 gm Volume = 24.8 ml = 0.0248 L (1 L = 1000 ml)

Q: What would be the sulfide-ion formality in a saturated solution of Bi2S3 if the Ksp of this compoun...

A: Bi2S3======> 2Bi ³+ + 3 S²- Suppose, “x” is the Solubility of Bismuth Sulphide....

Q: What is Lambda max and why do we need it?

A: Note: you have posted 2 different questions at same time. But As per bartleby guidelines I can solv...

Q: Calculate the osmotic pressure associated with 50.0 g of an enzyme of molecular weight 98,000 g/mol ...

Q: How many grams of magnesium hydroxide will precipitate if 25.0 mL of 0.235 M magnesium nitrate with ...

Q: What volume of 0.120 M NaOH must be added to 100 mL of 0.100 M NaHC204 to reach a pH of 4.70? H2C204...

A: The solution is given below -

Q: Fe+ (aq) + SCN (aq) = FeSCN²+ (aq) A solution is made containing an initial Fe+] of 1.2 × 10-3 M and...

Q: Problem 2: Use the labels E and Z to best describe the stereochemistry of the alkenes below. OH NH2 ...

Q: ar Orbital Theory ct a molecular orbital diagram for peroxide ion, O2². Is peroxide ion paramagnetic...

A: We have to draw the molecular orbital diagram for O2-2.

Q: If you have 6370 km When you convert that to meters how do you get 6.37 x 10 ^6 ?

A: Kilometre is unit of distance. It is denoted by symbol Km. Other units of distance is meter.

Q: Question 1 You will observe a weak acid-strong base titration in this experiment. Select all stateme...

A: Please find your solution below : The acid-base titration is a technique which is used to determine ...

Q: With an increasingly growing population, space for growing food is essential. This will restrict cro...

A: Alternative fuels for future - Among the four given alternative fuels these two can be used as alte...

Q: When 22.0 mL of a 8.35x10-4 M silver acetate solution is combined with 15.0 mL of a 5.74x10-4 M sodi...

A: The reaction quotient (Q) determines by a precipitate will form with a given concentration of ions. ...

Q: The hydronium ion concentration of an aqueous solution of 0.412 M codeine (a weak base with the form...

Q: Predict the products of the electrolysis of an aqueous solution of sodium chloride in cell using pla...

A: Electrolysis is a spontaneous redox process Here we are required to find the product when aqueous so...

Q: CH2=C=CH-CH2-CH2-CH=CH2 C= C-CH3 3. fra 1. 2.

Q: A student dissolves 10.6 g of ammonium nitrate (NH,NO, in 200. g of water in a well-insulated open c...

Q: In the titration of 145.0 mL of 0.4000 M HONH, with 0.2000 M HBr, how many mL of HBr are required to...

Q: Calculate the solubility of solid Ca3(PO4)2 (Ksp=1.3 x 10^-32) in a .20 M Na3PO4 solution.

Q: B1

A: To write the IUPAC name for the following:-

Q: An action will release carbon tetrachloride to the atmosphere resulting in an air concentration at t...

A: Given:- An action will release carbon tetrachloride to the atmosphere resulting in an air concentrat...

Q: o-chloroiodobenzene 2. 7-ethynyldecatri-1,3,9-triene 3. 2-bromo-2,3-dimethylpetan-2-c 4. 2-bromo-5-e...

Q: Mechanism of Possible Action Specific Use Dehydrating agent Description Preventive Toxicity measures...

A: Since you have asked a question with multiple subparts we will answer the first one for you. To get ...

Q: The following alkyl azide (R-N3) can be synthesized in two synthetic steps. Propose a two step synth...

A: Both the steps occurs via Sn2 mechanism. In 1st reaction, OH is not a good leaving group. In presen...

Q: N204 + 2 NO2 The K, for the reaction above is 2.40 x 10-2 at 1143.15 K. Assume that the initial conc...

Q: I make a buffer solution from of 5.0 mL of 0.500 M sodium acetate (NaCH3COO) and 45.0 mL of 0.500 M ...

A: Given, [CH3COOH] = 0.500 M Volume of CH3COOH = 45.0 mL [CH3COONa] = 0.500 M Volume of CH3COONa =...

Q: The pH of an aqueous solution of 8.39×10-2 M ammonium nitrate, NH4NO3 (aq

Q: MULTIPLE CHOICE Question 18 Which scenario best describes the long-term health effect of air polluti...

A: Here, we have to find the best scenario that describes the long-term health effect of air pollution ...

Q: Calculate the final pH of the undiluted buffer after 0.25 mL (5 drops) of 0.1 M NaOH is added. Ka of...

Q: Calculate the energy required to heat 425.0 g of water from 25.2 °C to 34.6 °C. Assume the specific ...

A: Given:- Calculate the energy required to heat 425.0 g of water from 25.2 °C to 34.6 °C. Assume the s...

Q: 2b) I dentify the nucleophillie carben atoms by drawing their formal charges. aiom bearng ane or mor...

A: In this molecule all the carbon atoms doesn't contain any formal negative charge. Therefore there is...

Q: The following alkyl azide (R-N3) can be synthesized in two synthetic steps. Propose a two step synth...

A: In the alcohol, the hydroxy group is a very poor leaving group in nucleophilic substitution reaction...

Q: What will be the equilibrium concentration of H2O?

Q: 1. Given a one-dimensional random coil with in total 1000 monomers, the bond length between two adja...

A: Sub-atomic displaying and reproductions are significant instruments for the polymer science and desi...

Q: A copper rod was purified by using it as the anode in the electrolysis of a 1.0 M copper II) sulphat...

Q: The hydroxide ion concentration, [OH-], of an aqueous solution of 0.424 M ethylamine (a weak base wi...

Q: Solve it asap with explanation..

A: What are the sources of triglycerides in the soap reaction ?

Q: 14) Obtain the major product for 1,2- and 1,4-addition reactions (a and b) of conjugated system firs...

A: Given:-

Question

00
%24
0
y
4
%23
V
)
dy
is the final temperature of the part (c of Al = 0.900 J/g K)?
A 359-g aluminum engine part at an initial temperature of 24.60°C absorbs 66.2 kJ of heat. What

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

When 50.0 g of 0.200 M NaCl(aq) at 24.1 C is added to 100.0 g of 0.100 M AgNO3(aq) at 24.1 C in a calorimeter, the temperature increases to 25.2 C as AgCl(s) forms. Assuming the specific heat of the solution and products is 4.20 J/g C, calculate the approximate amount of heat in joules produced.
A 237-g piece of molybdenum, initially at 100.0 C, is dropped into 244 g of water at 10.0 C. When the system comes to thermal equilibrium, the temperature is 15.3 C. What is the specific heat capacity of molybdenum?
Peanuts and peanut oil are organic materials and bum in air. How many burning peanuts does it take to provide the energy to boil a cup of water (250 mL of water)? To solve this problem, we assume each peanut, with an average mass of 0.73 g, is 49% peanut oil and 21% starch; the remainder is noncombustible We further assume peanut oil is palmitic acid, C16H32O2, with an enthalpy of formation of 848.4 kJ/mol. Starch is a long chain of C6H10O5 units, each unit having an enthalpy of formation of 960 kJ.
A 5.00-g sample of aluminum pellets (specific heat capacity = 0.89 J/C g) and a 10.00-g sample of iron pellets (specific heat capacity = 0.45 J/C g) are heated to 100.0C. The mixture of hot iron and aluminum is then dropped into 97.3 g water at 22.0C. Calculate the final temperature of the metal and water mixture, assuming no heat loss to the surroundings.
A piece of aluminum with a mass of 250. g is at an initial temperature of 5.0 C. If 24.1 kJ is supplied to warm the Al, calculate its final temperature. Obtain the specific heat capacity of Al from Table 4.1. Table 4.1 Representative Specific Heat Capacities
A 250-g sample of water at 20.0C is placed in a freezer that is held at a constant temperature of 20.0C. Considering the water as the system, answer the following questions: a What is the sign of qsys for the water after it is placed in the freezer? b After a few hours, what will be the state of the water? c How will the initial enthalpy for the water compare with the final enthalpy of the water after it has spent several hours in the freezer? d What will the temperature of the water be after several hours in the freezer?
9.53 Using these reactions, find the standard enthalpy change for the formation of 1 mol of PhO(s) from lead metal and oxygen gas. PbO(s)+C(graphite)Pb(s)+CO(g) H = 106.8 kJ 2C(graphite)+O2(g)2CO(g) H= -221.0 kJ If 250 g of lead reacts with oxygen to form lead(II) oxide, what quantity of thermal energy (in kJ) is ahsorhed or evolved?
9.100 Two baking sheets are made of different metals. You purchase both and bake a dozen cookies on each sheet at the same time in your oven. You observe that after 9 minutes, the cookies on one sheet are slightly burned on the bottom, whereas those on the other sheet are fine. (You are curious and you vary the conditions so you know the result is not caused by the oven.) (a) How can you use this observation to infer something about the specific heat of the materials in the baking sheets? (b) What is themathematical reasoning (equation) that you need to support your conclusion?
Microwave ovens convert radiation to energy. A microwave oven uses radiation with a wavelength of 12.5 cm. Assuming that all the energy from the radiation is converted to heat without loss, how many moles of photons are required to raise the temperature of a cup of water (350.0 g, specific heat =4.18J/gC) from 23.0C to 99.0C?
Nitric acid, HNO3, can be prepared by the following sequence of reactions: 4NH3(g)+5O2(g)4NO(g)+6H2O(g)2NO(g)+O2(g)2NO2(g)3NO2(g)+H2O(l)2HNO3(l)+NO(g) How much heat is evolved when 1 mol of NH3(g) is converted to HNO3(l)? Assume standard states at 25 C.
9.104 An engineer is using sodium metal as a cooling agent in a design because it has useful thermal properties. Looting up the heat capacity, the engineer finds a value of 28.2 J mol-l °C-l. Carelessly, he wrote this number down without units. As a result, it was later taken as specific heat. (a) What would he the difference between these two values? (b) Would the engineer overestimate the ability of sodium to remove heat from the system or underestimate it because of this error? Be sure to explain your reasoning.
In a coffee-cup calorimeter, 100.0 mL of 1.0 M NaOH and 100.0 mL of 1.0 M HCI are mixed. Both solutions were originally at 24.6C. After the reaction, the final temperature is 31.3C. Assuming that all the solutions have a density of 1.0 g/cm3 and a specific heat capacity of 4.18 J/Cg, calculate the enthalpy change for the neutralization of HCl by NaOH. Assume that no heat is lost to the surroundings or to the calorimeter.