A 3m - long snow plow attached to the truck is shown on the road he cleans the snow. Snow thickness is 30 cm and snow density is 200 kg / m has been given. The truck is travelling at 54 km / h and is driven by a snow plow 60° angle with the bed in the direction of the truck's movement as shown is divided. Calculate the force required to push the snow shovel. Abdomen it is accepted that it acts as a fluid. V = 54 km / li 6 0

A 3m - long snow plow attached to the truck is shown on the road he cleans the snow. Snow thickness is 30 cm and snow density is 200 kg / m has been given. The truck is travelling at 54 km / h and is driven by a snow plow 60° angle with the bed in the direction of the truck's movement as shown is divided. Calculate the force required to push the snow shovel. Abdomen it is accepted that it acts as a fluid. V = 54 km / li 6 0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
The diameter of the ball is 30 cm as shown in the figure. Calculate the river current velocity [m/s]. (NOTE: Neglect the weight of the cable. SGBALL = 0,20 PWATER = 1000 KG/M3 CD,BALL=0,12
Air flows along a horizontal, curved streamline with a 5.486 m radius with a speed of 31.09 m/s. Determine the magnitude of pressure gradient normal to the streamline. Take rho = 1.2266 kg/m3
The diameter of the ball is 30 cm as shown in figure. Calculate the river current speed m/s. (NOTE: Neglect the weight of the cable. Assume; SGpal=0.20, pwater-1000 kg/m and Cobal=0,2)
Water (density 1000 kg/m3) is flowing past a long cylinder at 1 m/s. The cylinder has a diameter of 0,05 m and a length of 0,4 m. The axis of the cylinder is perpendicular to the distraction of flow. What is the force on the cylinder in N?
An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasoline would begin to spill? notw: include free body diagram
Spaces h1=15 mm and h2=20 mm wide between upper and lower stationary plates and a very thin moving plate is filled with crude oil (oil =7.18x10-3 Pas) and water (water =1.00x10-3 Pas), respectively. What force is required to drag the plate of 0.5 m2 area between the surfaces at a speed of v=0.15 m/s. Assume linear velocity profile
Flood in irrigation areasto block and return the water to the river or wateras below to guide your bedThe flat cover system provided is preferred. Of coverits weight is 871 kg. Square section cover, coverhinged 1 m above center (a = 0.25 m)and b = 150 cm. Cover vertically 4 °has angle. According to the givenWhat is the maximum water head (h) for not openingshould be up. (ρ water = 1000 kg / m3)
You bet your friend that he cannot completely submerge your beach ball, which has a diameter of 60 cm and negligible mass. He must balance on the beach ball, not jump on it. What is the smallest mass that your friend can have and be successful? Assume that the sea water density is 1024kg/m^3.
The density of a floating body can be determined by tying weights to the body until both the body and the weights are completely submerged, and then weighing them separately in air. Consider a wood log that weighs 1540 N in air. If it takes 34 kg of lead (r 5 11,300 kg/m3) to completely sink the log and the lead in water, determine the average density of the log.
There are two liquids in the container in the picture: oil of density ρu=820kg/m3 and water of density ρw=998 kg / m3. Calculate max. pressure in the vessel if it rotates at an angular velocity ω=10 s-1. D=0.76m, H=0.9m, h1=0.3m, h2=0.45m
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 m is filled with a liquid (SG > 1, like glycerin) and the rest with water, as shown in the figure. The tank is now rotated about its vertical axis at a constant angular speed of ω. Determine (a) the value of the angular speed when the point P on the axis at the liquid-liquid interface touches the bottom of the tank and (b) the amount of water that would be spilled out at this angular speed.