A 4m long board is oriented in the horizontal plane, supported by vertical chains as each end of the board. The board has a uniformly distributed weight 125 N. A 500n person stand on the board. The tension in the right chain is 250 N. How far from the left end of the board is the person sitting? а. 2 m b. 0.4 m с. 3 m O d. 1.5 m O e. 2.5 m

A 4m long board is oriented in the horizontal plane, supported by vertical chains as each end of the board. The board has a uniformly distributed weight 125 N. A 500n person stand on the board. The tension in the right chain is 250 N. How far from the left end of the board is the person sitting? а. 2 m b. 0.4 m с. 3 m O d. 1.5 m O e. 2.5 m

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Dynamics

Section: Chapter Questions

Problem 34P

See similar textbooks

Similar questions

A man stands a distance d = 0.275 m from the left end of a platform as shown in the figure. The platform is supported by three cables. Find the tension in each cable (in N). Assume the platform is uniform, with length L = 2.00 m and mass 35.0 kg, and the weight of the man is 690 N. (Due to the nature of this problem, do not use rounded intermediate values in your calculations—including answers submitted in WebAssign.) (b). What If? The man now begins to walk to the right. If each of the cables can support a maximum tension of 800 N, which cable fails first? At what location does this occur (measured in m from the left end of the platform)?
A 104.8N tightrope walker stands at the center of the rope such that each half of the rope makes an angle of 8 degrees with the horizontal. What is the tension in the rope? ROUND TO 3 DECIMAL PLACES
A 8-m uniform beam of weight 120 N is supported by two ropes at the ends. If a 500-N person sits at 3.0 m from the left end of the beam, (a) what is the tension in the right rope? (b) What is the tension in the left rope?
A uniform beam is 5.00 m long and has a mass of 53.0 kg. The beam is supported in a horizontal position by a hinge and a cable, with angle ? = 115°.(a) Draw all the forces acting on the beam.(b) What Newton’s Law will you use to solve this problem?(c) What is the tension ?? on the cable?(d) What are the magnitude of the vertical and horizontalforces acting on the hinge ???(e) What is the magnitude and direction of the torque ??exerted by the tension on the cable?
1. Write an expression for the y-component Py of the force exerted by the pivot on the beam. 2. Write an expression for the tension T in the horizontal cable AB 3. Write an expression for the x-component Px of the force exerted by the pivot on the beam, in terms of T. 4. What is the tension in the horizontal cable, in newtons, if the mass of the beam is 34 kg, the length of the beam is 14 m, and the angle is 36°?
A hiker, who weighs 659 N, is strolling through the woods and crosses a small horizontal bridge. The bridge is uniform, weighs 4280 N, and rests on two concrete supports, one on each end. He stops 1/5 of the way along the bridge. What is the magnitude of the force that a concrete support exerts on the bridge (a) at the near end and (b) at the far end?
(a) When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850m from the hinges. What torque are you exerting relative to the hinges? (b) Does it matter if you push at the same height as the hinges?
A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00 m from the right end. What is the magnitude of the force exerted on the plank by the support near the right end? (a) 32.0 N (b) 45.2 N (c) 112 N (d) 131 N (e) 98.2 N
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
(a) What force should the woman in Figure 9.45 exert on the floor with each hand to do a push-up? Assume that she moves up at a constant speed. (b) The triceps muscle at the back of her upper arm has an effective lever arm of 1.75 cm, and she exerts force on the floor at a horizontal distance of 20.0 cm from the elbow joint. Calculate the magnitude of the force in each triceps muscle, and compare it to her weight. (c) How much work does she do if her center of mass rises 0.240 m? (d) What is her useful power output if she does 25 pushups in one minute?
A painter of mass 87.8 kg is 1.45 m from the top of a 6.67-m ladder. The ladder rests against a wall. Friction between the ladder and the wall is negligible. The ladders mass is 5.50 kg. Assume the ladder is set up according to Occupational Safety and Health Administration standards so that it makes a 75.5 angle with the floor. a. What is the minimum coefficient of static friction required for the painters safety? b. Would rubber ladder tips on dry concrete be safe?
A horizontal 4.0 m long 5.0 N uniform bar at one end is attached to a wall by a frictionless hinge; and at the middle of the bar there is a vertical cable pulling down 7.0 N, and at the middle of the bar there is also a cable that is at 45 ° to the horizontal pulling up as shown. i) What is the tension of the upper cable?