A 50-mm diameter nozzle is attached to a 300-mm diameter pipe by flange bolts as shown.Assume that the headloss throughout the nozzle is 10 meters. The fluid exits the nozzle asa free jet. The fluid flowing in the pipe is water with specific weight of 9810 N/m³.300 mmpipe50 mmnozzleBAflange boltsDetermine the discharge if the pressure at the base (point A) is 500 kPa.a.1.623 cmsb.0.062 cmsc.0.056 cmsd.2.020 cmsWhat will be the total tension on the bolts if the pressure at the base (point A) is 500 kPa?a.33,432 Nb.33,807 Nc.37,253 Nd.36,878 N

This problem is related to the flow measurement topic. the given diagram shows a conversing…

A 50-mm diameter nozzle is attached to a 300-mm diameter pipe by flange bolts as shown. Assume that the headloss throughout the nozzle is 10 meters. The fluid exits the nozzle as a free jet. The fluid flowing in the pipe is water with specific weight of 9810 N/m³. 300 mm pipe 50 mm nozzle A flange bolts Determine the discharge if the pressure at the base (point A) is 500 kPa. a.1.623 cms b.0.062 cms c.0.056 cms d.2.020 cms What will be the total tension on the bolts if the pressure at the base (point A) is 500 kPa? a.33,432 N b.33,807 N c.37,253 N d.36,878 N

A 50-mm diameter nozzle is attached to a 300-mm diameter pipe by flange bolts as shown. Assume that the headloss throughout the nozzle is 10 meters. The fluid exits the nozzle as a free jet. The fluid flowing in the pipe is water with specific weight of 9810 N/m³. 300 mm pipe 50 mm nozzle A flange bolts Determine the discharge if the pressure at the base (point A) is 500 kPa. a.1.623 cms b.0.062 cms c.0.056 cms d.2.020 cms What will be the total tension on the bolts if the pressure at the base (point A) is 500 kPa? a.33,432 N b.33,807 N c.37,253 N d.36,878 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops in the suction and discharge are 3 m and 4 m, respectively. ZA = 15m, ZB = 5m and ZC = 5m.
When a pitot tube as shown below is placed in a river with its lower open end facing upstream, water rises in the vertical portion to a height of 50mm above the water surface. Find the flow velocity U. [density of water ρ = 1000kg/m3]
Water is flowing out of the nozzle (2) into atmospheric pressure (101 kPa). What is the horizontal force exerted by the flange to hold the nozzle (2) attached to the pipe (1)? Flow velocity at point (2) is 8 m/s. Water density is 1000 kg/m3.
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A horizontal nozzle discharges water into the atmosphere as shown in the figure, being the relative pressure at point 1 equal to p1 = 20 kPa A Pitot tube connected to a mercury manometer is inserted into the flow in area section A1 indicating a height difference h = 0.02 m. For this reading indicated in the Pitot tube, determine the speed in the Area A1 section of the nozzle. For docking block sizing it is necessary to determine the force that the nozzle applies to the fluid. Calculate the component of this force in the x direction. Data: D1 = 0,075 m; D2 = 0,055 m; θ = 30° ; dHg = 13,6.
A 15-ft-diameter tank discharges water at 50 F through a 2-in.-diameter sharp edged orifice. If the initial water depth in the tank is 10 ft and the tank is continuously pressurized to 50 psi, how long will it take to empty the tank?
Show that the quantity of water flowing across a triangular V-notch of angle 2θ isQ = Cd(8/15)tan (θ/2)(2g)1/2H 5/2 . Find the flow if the measured head above the bottom of the V is 70cm,when θ =120 o and Cd = 0.6.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
A sharpedged orifice has a diameter of 1′′ and coefficients of velocity and contraction of 0.98 and 0.62, respectively. If the jet drops 3.08 ft in a horizontal distance of 8.19 ft, determine the flow in cfs and the head on the orifice.
A horizontal nozzle discharges water into the atmosphere as shown in the figure. the relative pressure at point 1 equal to ?1 = 18 ??? . A. A Pitot tube connected to a mercury manometer is inserted into the flow. in the area section A1 indicating a height difference ℎ = 0.01 m. For this reading indicated in the Pitot tube, determine the velocity in the A1 area section of the nozzle. B. For the dimensioning of the anchor block it is necessary to determine the force that the nozzle applies over the fluid. Calculate the component of this force in the x direction. Data: ?1 = 0.070 ?; ?2 = 0.060 ?; ? = 30°; ??? = 13.6
Water is siphoned from a large tank through a pipe diameter equal to 30 mm. Assuming viscous interactions are negligible and that the atmospheric pressure is 101kPa, determine the following: (a) The exit velocity? (b) The maximum height of h of the siphon tube if the absolute pressure along the centerline is not to fall below 50 kPa?
Consider the water siphon shown, if the tube is 1 cm in diameterand z1 = 60 cm, z2 = -25 cm, z3 = 90 cm and z4 = 35 cm, estimatethe flowrate in cm3/s.