A 60° bend occurs in a water pipeline that reduces from 600 mm diameter to 300 mm diameter at the bend (inside bend angle 120). If the gauge pressure at the inlet is172 KPa, determine the magnitude ad angle of the thrust on the bend when the flow is 0.85 m3/s. Hint: start by calculating the initial and final velocities, then the finalpressure. Next, analyze the pressure and momentum forces in the x and y planes.

Given: Inlet diameter and outlet diameter are 600 mm and 300 mm. Gauge pressure at the inlet is…

Answered: A 60° bend occurs in a water pipeline…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing into and discharging from a pipe U-section as shown . At flange (1), the total absolute pressure is 200 kPa, and 55 kg/s flows into the pipe. At flange (2), the total pressure is 150 kPa. At location (3), 15 kg/s of water discharges to the atmosphere, which is at 100 kPa. Determine the total x- and z-forces at the two flanges connecting the pipe. Discuss the significance of gravity force for this problem. Take the momentum-flux correction factor to be 1.03 throughout the pipes
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
A 3"-diameter jet has a velocity of 110 fps. It strikes a blade moving in the same direction at 70 fps. The deflection angle is 150°. Assuming no friction, determine the final absolute velocity of the water V2 as it leaves the blade.
A rocket motor is fired in place on a test stand. The rocket exhausts 10 kg/s at an velocity of 800 m/s. Assume uniform steady conditions at the exit plane with an exit plane static pressure of 50 kPa. For an ambient pressure of 101 kPa, determine the rocket motor thrust transmitted to the test stand
A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the pressure is 138 kN/m2. If the pipe tapers gradually from 150mm diameter at A to 100mm diameter at location B, determine the pressure of the water at B, assuming there is no loss of energy.
Assuming that the fluid enters to the pump with no shock / no swirl, construct the velocity triangles at both inner and outer diameters of the impeller for the case where the blade angle at the outlet is: β2 = 90o, and β2 = 130o
The jet shown strikes the semicircular vane horizontally. Estimate the horizontal force on the vane. Since this is in British units, use ρ = 1.94 slug/cfs Pls hand written solution
An elbow deflects water upward and discharges it to the atmosphere at a specific rate. Determine the gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place. (gage pressure at the outlet is zero)
The pump in the figure draws water from an 8-in. suction pipe and discharges through a 6-in. pipe in which the velocity is 12 ft per second. The pressure is -5 psi at A in the suction pipe. The 6-in pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 6 ft above A and 20 horsepower is delivered to the pump? Assume that the pump operates at 70 percent efficiency and that the frictional loss in the pipe between A and C is 10 ft.
The drawing shows a centrifugal fan. The fan draws 25 m^3/s of air from the room through the 0.75 diameter bellmouth inlet. The air is discharged into a 0.5 m diameter pipe which is connected to the downstream piping by a flexible connector. Note that the flexible connector does not transmit any forces or momentum between the connected components. Determine the forces in the x and y directions which the floor must apply to hold the fan in place. Assume incompressible flow with p=1.3 kg/m^3. Atmospheric pressure is 101 kPa.
Air is exhausted from the fixed jet engine at 20 kg/skg/s with a velocity of 420 m/sm/s while it is being tested with an attached brake deflector. Determine the magnitude of the force in each of the two supporting links needed to hold the deflector in the position shown in
Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute pressure is 240 kPa, and water flows into the pipe at 42 kg/s. At flange (2), the total pressure measured is 190 kPa with a flow rate of32 kg/s. At point (3) water discharges into the atmosphere at 90 kPa at a flowrate of 10 kg/s. The mass of the elbow and the water in it is 50 kg. Neglecting the momentum-flux correction factor, determine the net x- and z-force at the two flanges connecting the pipe.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS