Answered: a) A battery having an emf (ɛ) of 9V…

a) A battery having an emf (ɛ) of 9V and an internal resistance (r) of 0.40 is connected to a load of 250 as shown below. What will be the readings in the ammeter and the voltmeter? A RLOAD V

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 10.6CYU: Check Your Understanding In considering the following schematic and the power supplied and consumed...

See similar textbooks

Related questions

Q: A flash unit for a camera has a capacitance of 1700 μF. What resistance is needed in this RC circuit…

Q: An auto mechanic needs to determine the emf and internal resistance of an old battery. He performs…

A: The auto mechanic performs two measurments.

Q: A battery has an emf of 15.0 V. The terminal voltage of the battery is 10.6 V when it is delivering…

Q: A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.4 V when it is delivering…

Q: The RC circuit shown in the figure has resistance of R=7k2 and the capacitance of C=10µF. The…

Q: An ohmic appliance is rated at 100. W when it is connected to a 120. V source. a) If the power…

Q: A capacitor of capacitance C is discharging through a resistance R. (A) in terms of the time…

A: Given: capacitance c resistance R time constant T=RC

Q: The batteries are ideal, and &=2E,. The three resistors have the same resistance value: R, = R, =…

Q: A 2002 load receives power from parallel-connected battery cells, as shown in the figure below.…

A: r1 = 1 ohm V1 = V2 = 12 V r2 = 1 ohm R = 20 ohm

Q: wwwwww- a •b n the arrangement of the resistors shown in the figure, all resistors have identical…

A: All resistors have identical resistance R, we have to have to find equivalent resistance R between a…

Q: What are the expected readings of (a) the ideal ammeter and (b) the ideal voltmeter in Figure?

A: A voltmeter is used to measure voltage between two points and will be connected parallelly between…

Q: Copper wire of diameter 0.259 cm is used to connect a setof appliances at 120 V, which draw 1450 W…

A: Given data: Diameter of the wire, d=0.259 cm = 0.259×10-2 m Voltage, V=120 V Power, P=1450 W…

Q: 1. A capacitor is charged to a potential of 12.0 V and then connected to a voltmeter having an…

A: Given Data :- The initial potential of the capacitor is Vi = 12.0 V. The internal resistance of the…

Q: Assume you have a battery of emf ε and three identical lightbulbs, each having constant resistance R…

A: The equation for the net resistance in a parallel connection is given as,

Q: In the circuit shown, the battery voltage, V = 15V and the load resistance, R = 15N. +, V ww R V A…

A: REcall Ohm's law V=IR

Q: What are the expected readings of the following in the figure below? (R = 9.30 N, AV = 6.20 V) R Δν…

Q: Determine the value of resistance R if the equivalent resistance in Figure below is 100 Q and…

Q: A flash unit for a camera has a capacitance of 1300 µF. What resistance is needed in this RC circuit…

Q: What are the expected readings of the following in the figure below? (R = 5.80 N, AV = 6.50 V) A R…

A: The current does not flow through the ideal voltmeter, so it will act as an open circuit. There is…

Q: A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.4 V when it is delivering…

A: a) We know that power P= V2/R R= 11.42/16 R= 8.12Ω

Q: H.W. 2.3: Find the equivalent resistance of the network between the terminals A and B shown in the…

Q: What are the expected readings of the following in the figure below? (R = 5.50 0, AV = 6.70 V) R ΔVν…

Q: You are asked to measure e.m.f of a cell. Which instrument will you use? A high resistance Voltmeter…

A: The potentiometer is used to measure the e.m.f of cell.

Q: A battery with an emf of 12.0 V has a terminal voltage of11.5 V when the current is 3.00 A. (a)…

A: a)Terminal voltage is given by

Q: Assume you have a battery of emf ε and three identical lightbulbs, each having constant resistance R…

A: Given: E.m.f. of battery = ε. Resistance of bulb = R. Number of bulb = n. Bulbs are connected in…

Q: What are the expected readings of the following in the figure below? (R = 5.60 N, AV = 6.30 V) R AV…

A: Given: The resistance R=5.6 Ω The voltage ∆V=6.3 volt

Q: R= 1.50 ohms 0.50 ohms 10.0V A real battery is connected to resistor R as shown. Calculate the…

A: Given data: Load resistance (R) = 1.50 Ω Internal resistance (r) = 0.50 Ω Battery emf (ε) = 10.0 V…

Q: In Figure 7.92, the ammeter reads 2.0 A and the volmeter reads 2.0 V. Use this information to find…

A: (a) The current I1 passing through the following circuit in clock-wise direction. The current is…

Q: What are the expected readings of the following in the figure below? (R = 9.50 N, AV = 6.50 V) R AV…

Q: The electromotive force of a battery is given by E = 8 volts. A resistor wtih resistance R1 = 24 kSN…

A: NOTE- Since the question in the 2nd image is graded, we will only solve the question mentioned in…

Q: A toy battery has an emf of 33.0 V. The terminal voltage of the battery is 15.50 V when it is…

Q: In the following Figure, the current in resistance R, is i,= 14A and the resistances are R, =R, = R;…

Q: What are the expected readings of the following in the figure below? (R = 6.40 Ω, ΔV = 5.30 V) (a)…

A: Given data The value of resistance is: R = 6.40 Ω The potential difference is: ∆V= 5.30 V The…

Q: What are the expected readings of the following in the figure below? (R = 6.70 N, Av = 5.30 V) R AV…

A: We will use KVL and KCL for the three loops and will find current through ammeter.

Q: 1.00 MQ A conducting sphere is charged by an emf source & through a 1.00 MO resistor. When the…

A: Given, Resistance,R=1 MΩ=106Ω Current,I=1 mA=10-3A Charge on sphere,Q=2μC=2×10-6C

Q: A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.0 V when it is delivering…

A: Given data The emf of the battery is: V = 15 V The terminal voltage of the battery is: Vter = 11 V…

Q: Consider the circuit shown in (Figure 1). For related problem-solving tips and strategies, you may…

Q: A capacitor is charged from the battery with EMF E = 10 V through the resistor R. What energy is…

Q: 1. As seen in the figure, the ideal batteries have emfs E1 = 16.0 V and ɛ2 = 4.00 V, and the…

Q: A battery has an emf of 15.0 V. The terminal voltage of the battery is 10.8 V when it is delivering…

Q: In the circuit below, when the switch (“S”) is open the Voltmeter (“V”) reads 3.08 V. When the…

A: Emf of the battery is the reading in the voltmeter when the switch is open. Thus, it is given by…

Q: A total resistance of 3.05 is to be produced by connecting an unknown resistance to a 12.01 Q…

A: Given: The total resistance is 3.05 Ω. The known resistance is 12.01 Ω.

Question

100%

23a

a) A battery having an emf (ɛ) of 9V and an internal
resistance (r) of 0.40 is connected to a load of
250 as shown below. What will be the readings in
the ammeter and the voltmeter?
RLOAD
i) The ammeter reading will be =
%3D
A
ii) The voltmeter reading will be =
V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Why should you not connect an ammeter directly across a voltage source as shown below?
Calculate the emfx of a dry cell for which a potentiometer is balanced when Rx = 1.200 Ω , while an alkaline standard cell with an emf of 1.600 V requiresRs = 1.247 Ω to balance the potentiometer.
Attached is a figure that shows a source (a battery) with emf = Ɛ = 12V andinternal resistance of 2 Ω . We add another 4 Ω resistor to the battery, forming a complete circuit . What are the voltmeter and ammeter readings and I ?Note : The ideal ammeter has zero resistance, so the total resistance external to thesource is R = 4 Ω. Where the current through the circuit aa’b’b is then
A heart defibrillator being used on a patient has an RC time constant of 11.0 ms due to the resistance of the patient asnd the capacitance of the defibrillator. If the defibrillator has an 7.25uF capacitance, what is nthe resistance of the path through the patient? If the initial voltage is 12.0 kV, how long does it take to declineto 427 V?
Why can a null measurement be more accurate than one using standard voltmeters and ammeters? What factors limit the accuracy of null measurements?
Integrated Concepts. A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. At what rate (in oC/min ) will its temperature increase if its mass is20.0 kg and it has a specific heat of 0.300 kcal/kg. oC, assuming no heat escapes?
A galvanometer has a coil resistance of Rgalv=22.4⁢ Ω. It is to be made into a voltmeter with a full‑scale voltage equal to V=265.0 V. If the galvanometer deflects full scale for a current of Igalv=195.5 mA, what size additional resistor should be used?
If E = 7.50V and r=0.45Ω, find the minimum value of the voltmeter resistance RV for which the voltmeter reading is within 1.0% of the emf of the battery.
A full capacitor with a capacity of 5 µF is discharged through a resistor of 8x105 Ω. Your loada) e the time of falling to someone andb) Find the halving time.
An astronaut uses a small motor, rated at 93% efficient, that is connected to a 12-volt [V] power supply on Mars. The motor has a resistance rating of 2.3 kiloohms [kΩ]. How long will it take to produce 3.4 calories [cal] of energy in units of minutes [min]?
A battery provides 12 volts on open circuit and it provides 11.6volts when delivering 2ampere .what is the intetnal resistance of the battery?
A heating element in a stove is designed to dissipate3.00 x 103 W when connected to 240. V. (a) Assuming theresistance is constant, calculate the current in the heatingelement if it is connected to 120. V. (b) Calculate the power itdissipates at that voltage.