(a) A hollow C15 steel(oy=235.4Mpa, oy=425Mpa shaft transmits 15kW at 250rpm as shown in figure Task 1a. It is supported on two bearings 750mm apart. A 500mm pulley whose weight is 1000N is keyed to the shaft at a distance of 100mm to the left of left bearing. A pinion having 75teeth and 4mm module is mounted at 150mm to the left of right bearing. The pulley is driven by a belt downward at an angle of 60°to the horizontal and towards the observer. The pinion drives a gear placed directly over it. Tension ratio=3 and diameter ratio=2. Determine the diameter of the shaft with ASME code. Assume the shaft rotates clockwise when viewed from right bearing and $=20⁰ (T₁+T₂) sin 60+ W, T₁+T₂ 60° (T₁+T.) cos 60 Driven Pulley A A Figure Task 1a

(a) A hollow C15 steel(oy=235.4Mpa, oy=425Mpa shaft transmits 15kW at 250rpm as shown in figure Task 1a. It is supported on two bearings 750mm apart. A 500mm pulley whose weight is 1000N is keyed to the shaft at a distance of 100mm to the left of left bearing. A pinion having 75teeth and 4mm module is mounted at 150mm to the left of right bearing. The pulley is driven by a belt downward at an angle of 60°to the horizontal and towards the observer. The pinion drives a gear placed directly over it. Tension ratio=3 and diameter ratio=2. Determine the diameter of the shaft with ASME code. Assume the shaft rotates clockwise when viewed from right bearing and $=20⁰ (T₁+T₂) sin 60+ W, T₁+T₂ 60° (T₁+T.) cos 60 Driven Pulley A A Figure Task 1a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
An industrial fan running at 600 rpm is driven by a 25kW, 960rpm, induction motor using an open belt drive. The pulley is mounted on the motor shaft of 270mm diameter. Center distance between the two shafts is 1.45 meters and coefficient of friction is 0.35. Assume thickness of belt equal to 6.5 mm and an allowable stress of 2.86MPa for belt material. Calculate the following: a) Angle of lap for both pulleys; b) Length of the belt; and c) Width of the belt (disregard standard size).
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
A 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20° stub teeth .the centre to centre distance between the shafts is 400mm.the motor pinion is made to forged steel having an allowable static stress 210MPa while the gear is made of cast steel having an allowable static stress as 140MPa.Assuming that the drive operates 8 to 10 hours per day under light shock conditions,find from the standpoint of strength (a) Module;(b)face width and (c)number of teeth an pitch circle diameter of each gear.check the gears thus designed from the consideration of wear .the surface endurance limit may be taken as 700MPa.
A gear reducer similar to Figure 3–1(a), transmits power from input shaft AB to output shaft CD. The input torque and constant speed are T = 200 lbf-in and ωi = 60 rev/min, respectively. The output load torque and speed are To and ωo, respectively. (c) Shaft AB, with diameter 0.5 in, is supported by ball bearings at A and B, which can be treated as simple supports. For this shaft, the dimension from A to gear G1 is 1.5 in, and gear G1 to B is 2 in. The pitch radii of the gears are r1 = 1.0 in and r2 = 2.5 in. For the spur gears, the pressure angle, ϕ, is 20 degrees. The book name is Shigleys Mechanical Engineering design 11th
A shaft is loaded in bending and torsion such that Ma = 62 N · m, Ta = 48 N · m, Mm = 54 N · m, and Tm = 25 N · m. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se = 210 MPa is assumed. Let Kf = 2.2 and Kfs = 1.8. With a design factor of 2.0 determine the minimum acceptable diameter of the shaft in mm using the DE-Goodman criterion.
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MP
A pair of straight teeth spur gear is to transmit 20kw when the pinion at 300rpm.the velocity ratio is 1:3.the allowable static stresses for the pinion and the gear material are 12MPa and 100MPa respectively.the service factor is 1.the pinion has 15 teeth and it's face width is 14 times the module.from the standpoint of strength only and taking into consideration the effect of the dynamic loading Determine; (A) module (B) face width (C) pitch circle diameter for pinion (D) pitch circle diameter for gear Tooth form factor;y=0.153_0.912÷no.of teeth Velocity factor;Cv= 3÷3+v
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
A shaft is required for a chain drive illustrated in figure 5.42. The power transmitted is 12 kW at 100 rpm. The masses of the sprockets are 5 and 16.3kg, with respective diameters of 254.6 and 460.8 mm. The material selected for the shaft is quenched and drawn 817M40 with ultimate tensile strength 850 MPa and yield strength of 700 MPa. The torque is transmitted between the shaft and sprockets by means of keys in profiled keyways. Determine the minimum diameter for the shaft based on the ASME equation for the design of transmission shafting if the desired reliability is 90 per cent. Use an initial estimate for the shaft diameter of 60 mm.