For the 3-phase system shown below, the source line voltage is 460 V, 60 Hz, 1). Phase "a" voltage, Vsa is Phase "b" voltage, Vs is Phase "c" voltage, Vs, is 2) What is the system phase sequence? 3). Line current, Isa is from the phase voltage, Vsa. 4). The total real power and reactive power provided by the source is (value and unit) and, L-120 V, and +120 V. A with degrees lagging/leading (circle one) (value and unit), respectively. Vs 6-j62 2+ j22 Load 1 Load 2

For the 3-phase system shown below, the source line voltage is 460 V, 60 Hz, 1). Phase "a" voltage, Vsa is Phase "b" voltage, Vs is Phase "c" voltage, Vs, is 2) What is the system phase sequence? 3). Line current, Isa is from the phase voltage, Vsa. 4). The total real power and reactive power provided by the source is (value and unit) and, L-120 V, and +120 V. A with degrees lagging/leading (circle one) (value and unit), respectively. Vs 6-j62 2+ j22 Load 1 Load 2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.6P

See similar textbooks

Similar questions

Draw an impedance diagram for the electric power system shown in the figure attached, showing all impedances in per unit on a 100-MVA base. Choose 20kV as the voltage base for generator. The three-phase power and line-line ratings are given in the figure attached.
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit error occurs at the F point in the Figure below İ k3 phase-max ?
A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral current
Write an introduction about: LOAD BALANCING in 3-Phase System
A three phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads.
Determine Zbus for the network shown in figure below using Direct Method, where the impedances labeled 1 through 4 are shown in per unit. Preserve all buses.
Describe the concept of power system harmonics and their impact on the quality of electrical supply.
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Power Transmission and Distribution Discuss the advantages and disadvantages of single-phase and three-phase system
c) Briefly explain about single phase and three phase power supply with diagrams.
1. Write down a formula for the three-phase active power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula for the three-phase reactive power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements 3. Write down a formula for the three-phase apparent power, assuming perfectly sinusoidal and symmetrical conditions, using line-neutral voltage measurements.