A battery with it's terminal volts is supplied with power from type-A chopper circuit. The output voltage of the chopper consists of rectangular pulses of 2 ms duration in an overall cycle time of 5 ms. The average, ms values of output voltage, ripple voltage and ripple factors are respectively (a) 80 V, 126.49 V, 149.66 V, 1.87 (b) 80 V, 126.49 V, 97.98 V, 1.87 (c) 80 V, 126.49 V, 149.66 V, 1.581 (d) 80 V, 126.49 V, 97.98 V, 1.2247

A battery with it's terminal volts is supplied with power from type-A chopper circuit. The output voltage of the chopper consists of rectangular pulses of 2 ms duration in an overall cycle time of 5 ms. The average, ms values of output voltage, ripple voltage and ripple factors are respectively (a) 80 V, 126.49 V, 149.66 V, 1.87 (b) 80 V, 126.49 V, 97.98 V, 1.87 (c) 80 V, 126.49 V, 149.66 V, 1.581 (d) 80 V, 126.49 V, 97.98 V, 1.2247

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 39CQ: An electronic apparatus may have large capacitors at high voltage in the power supply section,...

See similar textbooks

Similar questions

Refer to Figure 21.7 and the discussion of lights dimming when a heavy appliance comes on. (a) Given the voltage source is 120 V, the wire resistance is 0.400, and the bulb is nominally 75.0 W, what power will the bulb dissipate if a total of 15.0 A passes through the wires when the motor comes on? Assume negligible change in bulb resistance. (b) What power is consumed by the motor?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Show that the power dissipated by the load resistor is maximum when the resistance of the load resistor is equal to the internal resistance of the battery.
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
Find the current through a person and identify the likely effect on her if she touches a 120-V AC source: (a) if she is standing on a rubber mat and offers a total resistance of 300 k; (b) if she is standing barefoot on wet grass and has a resistance of only 4000 k .
To a series circuit, in which the capacitance is 15 x10 -6(farads) and the resistance is 1500 (ohms), a voltage of 210 V (volts). Evaluate (a) The capacitor charge if i(0) = 0.5.(b) Determine the charge q(t) and the current i(t) for t = 1.5 seconds.(c) Determine the load when t →∞
Integrated Concepts. A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. At what rate (in oC/min ) will its temperature increase if its mass is20.0 kg and it has a specific heat of 0.300 kcal/kg. oC, assuming no heat escapes?
What capacitance when connected in series with a 500Ω resistor will limit the current drawn from a 48-mV 465-kHz source to 20μA?
A 3.50 μμF capacitor that is initially uncharged is connected in series with a 7.60 kΩ resistor and an emf source with E=185 V negligible internal resistance. Just after the circuit is completed, what is the voltage drop across the capacitor? Just after the circuit is completed, what is the voltage drop across the resistor? Just after the circuit is completed, what is the charge on the capacitor? Just after the circuit is completed, what is the current through the resistor?
the voltage across a 3.71uf capacitor in a tv circuit is 4.54 mV. Find the voltage after 0.563ms if a current is given below (in uA) further changes the capacitor. i= (1+6t)^(1/3) The voltage at t = 0.563 ms is _________ mV. I have no clue on the steps to solve such a problem help would be greatly appreciated
A rule of thumb used to determine the internal resistance of a source is that it is the open-circuit voltage divided by the short-circuit current. Is this correct? Why or why not?
R1 is 150 ohms, and R2 is 220 ohms. (150 +220 = 370). In a series circuit, the current is the same across the circuit. The available power storage is 6 volts. The problem I am have is conceptualizing what V1 + V2 equals. I conjecture that the sum would be less than 6 V. I can't say 3 + 3 =6 V, but rather V1 + V2 < 6? Unless R1=R2, then perhaps 3 + 3 = 6V. However, R1 is 150 ohms, and R2 is 220 ohms. Complicating issue, if I use an ammeter and voltmeter, these devices may have some internal resistance, so equals becomes < 6 V? How then do I conceptualize better, V1 + V2, so that maybe it is based on the value of the individual Resistor?