A beam ABCDEF is 10 m long and is supported at points B and E which are 2 m and 9 m respectively from A towards the left-hand end. The beam carries a concentrated load of 10kN at A, a concentrated load of W kN at C, which is 5 m from A, and a concentrated load of 16 kN at D which is 4 m from point F. In addition a beam carries a uniformly distributed load of 4 kN/m from A to C and uniformly distributed load of 3 kN/m from D to F.

A beam ABCDEF is 10 m long and is supported at points B and E which are 2 m and 9 m respectively from A towards the left-hand end. The beam carries a concentrated load of 10kN at A, a concentrated load of W kN at C, which is 5 m from A, and a concentrated load of 16 kN at D which is 4 m from point F. In addition a beam carries a uniformly distributed load of 4 kN/m from A to C and uniformly distributed load of 3 kN/m from D to F.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.5.10P: .10 A built-up bourn supporting a condominium balcony is made up of a structural T (one half of a W...

See similar textbooks

Similar questions

A beam 8.5-m long is fixed at the left end and supported by a roller at a point 1.5-m from the right end. There is an internal hinge at a point 2.5m from the fixed end. The beam is loaded by a clockwise couple equal to 50 kN-m acting at a point 1-m to the right of the fixed end, a downward concentrated vertical load equal to 12- kN acting at a point 4.5-m to the right of the fixed end and a downward uniform vertical load equal to 5-kN/m starting at a point 4.5m from the fixed end up to the right end of the beam. Draw the shear and moment diagram of the beam .
A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed3.25 N/mm2 find the load w.
Draw the shear and bending-moment diagrams for a simply supported beam AB of span L subjected to a single concentrated load P at its midpoint C
) A simply supported beam of length L=12 m, carrying UDL 10 KN/m in its entire length of thebeam. Draw the Shear Force (S.F) and Bending Moment (B. M) of the beam.Write down the maximum value of B.M
A small balcony constructed of wood issupported by three identical cantilever beams (seefigure). Each beam has length L1 = 2.1m, width b,and height h = 4b/3. The dimensions of the balconyfloor are L1 XL2, where L2 = 2.5 m. The designload is 5.5 kPa acting over the entire floor area.(This load accounts for all loads except the weightsof the cantilever beams, which have a weight densityΥ = 5.5 kN/m3.) The allowable bending stress in thecantilevers is 15 MPa.Assuming that the middle cantilever supports50% of the load and each outer cantilever supports25% of the load, determine the required dimensions band h.
A symmetric frame PQR consists of two inclined members PQ and QR, connected at 'Q' with a rigid joint, and hinged at 'P' and 'R'. The horizontal Length PR is L. If a weight W is suspended at 'Q', the bending moment at 'Q' is
A cantilever beam is subjected to a concentrated load of 2000N. The cross sectional dimensions of the double-tee beam are shown. Determine (a) the shear stress at point H, which is 17 mm below the centroid of the double-tee shape, (b) the shear stress at point K, which is 5 mm above the centroid of the double tee shape, and (c) the maximum horisontal shear stress in the double tee shape.
A propped cantilever beam has flexural rigidity EI = 2.5 MN•m2. When the loads shown are applied to the beam, it settles at joint B by 5 mm. Find the reaction at joint B.
A linear elastic beam with length L, elastic modulus E, and second moment of an area I is fixed at end C and attached to a linear elastic spring at B. The spring has an elastic constant k. The beam carries a uniformly distributed load q. Determine the vertical deflection at point B and the reaction forces at C.
A uniform light beam has length 6 m. The lefthand side rests on a roller and the right hand sideis welded horizontally to a support. It bears a uniform load of 2 kN/m downwards, a concentrateddownwards load of 3 kN at x = 2 m and a concentrated anticlockwise couple of 4 kN.m at x = 4 m.Determine the form of the beam.
For the assembly shown below, the beam AB weighing 100 lbs is loaded with force P = 200 lbs. A frictionless pulley with radius "r" and weighing 80 lbs is attached at the end of the beam at point B, supported with two ropes inclined at angles x and y points at C and D. If a = 2 ft, b = 3 ft, angles x & y are 30 deg. and 40 deg. respectively and radius "r" is 6 inches,
A beam of rectangular section of 12 cm × 20 cm is simply supported over a span of 12 m. It is acted upon by a load of 80 kN at the mid span. Determine the maximum bending stress induced in thr beam.