A block of mass m slides on a horizontal rough surface head on into a spring of spring constant k = 730 N/m, as shown in Figure. When the block is x = 0.8 meter away from the spring, it has a velocity v = 4.33 m/s. When the block stops, it has compressed the spring by 6.5 cm. The coefficient of kinetic friction between the block and the surface is 0.1. What is the block's mass m (in kg)? Provide your answer with 2 decimal places. Take g = 9.81 m/s²

A block of mass m slides on a horizontal rough surface head on into a spring of spring constant k = 730 N/m, as shown in Figure. When the block is x = 0.8 meter away from the spring, it has a velocity v = 4.33 m/s. When the block stops, it has compressed the spring by 6.5 cm. The coefficient of kinetic friction between the block and the surface is 0.1. What is the block's mass m (in kg)? Provide your answer with 2 decimal places. Take g = 9.81 m/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sam, whose mass is 68 kg , straps on his skis and starts down a 68 m -high, 20∘ frictionless slope. A strong headwind exerts a horizontal force of 200 N on him as he skies. Use work and energy to find Sam's speed at the bottom.
1. Assuming that there are no heat effects and no frictional effects,find the kinetic energy and speed of a 3220lb body after it falls 778 ft from rest. Start with the steady flow equation, deleting energy terms which are irrelevant. Draw a figure or FBD that will support the problem. Explain each step by step formula.
A jet of water whose diameter is 5cm strikes a fixed cup with a velocity of 9.45m/s and is deflected by 165 degree. The jet leaves with a velocity of 30m/s . if the cup offers a reactive force of 26.5N to the jet when the flow rate was 980 N/min. Determine the ratio of a) Actual to theoretical forces of the jet. b) Velocities at outlet and inlet. Assume any missing data.
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
Topic: Impulse and Momentum Sand drops at a rate of 2000 kg/min from the bottom of a hopper onto a belt conveyer moving horizontally at 250 m/min. Determine the force needed to drive the conveyer, neglecting friction.
For the chain: linear density=p, length=1. The chain is placed on the smooth plane. As shown in the figure, the drooping length=b, the chain is stationary at this moment (v=0). Then, under the action of the gravity, the chain drop freely. Determine the sped of the chain when the left end of leave the plane.
The super-container vessel in the figure has a total mass displacement of (4000) long tons. This vessel towed by a tugboat with α=20⁰ angle with horizontal. If a constant tension is applied as F= 400 kN by the tugboat, please calculate the time to bring the vessel to a speed of 2 knot from the rest. At these low speeds, please neglect the hull resistance that created by the motion. Note: (1 long tons = 1016.05 kg, 1 knot=1.151 mi/hr= 0.5144 m/s)
A 50 kg inclined plane, 4 m long and 30 degrees in angle, rests without friction on a table (there is oil between the inclined plane and the table). A 20 kg mass is at the top of the inclined plane and slides without friction on it. How much will the inclined plane move when the mass reaches the table? What will be the speed of the inclined plane and the speed of the mass when the latter is on the table? (we have conservation of mechanical energy (no friction) and conservation of momentum...)
Describe Applications of momentum equations.
A windmill turns a series of slender rods fixed about one end . They are initially 2 meters long, and go at a speed of 15 revolutions per minute. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
A horizontal water jet with a 2.5 cm diameter and a speed of V =40 m/s relative to the ground is deflected by a 60° stationary cone whose base di ameter is 25 cm The height of water along the cone is 0.125cm. Disregarding the effect of gravity and the shear forces, the horizontal force F needed to hold the cone stationary is
As can often be seen in a kitchen sink when the faucet isrunning, a high-speed channel fl ow ( V 1 , h 1 ) may “jump” toa low-speed, low-energy condition ( V 2 , h 2 ) as in Fig. . The pressure at sections 1 and 2 is approximately hydrostatic,and wall friction is negligible. Use the continuity andmomentum relations to fi nd h 2 and V 2 in terms of ( h 1 , V 1 ).