A body is loaded as shown in Figure 2 where P 80 kN and Q = 3 kN. In addition, the following information is known X1 = 2 m X2 = 2 m Y1 = 3 m Z1 = 3 m 22 3 m In the question that follows, select the answer that is closest to the true value. What is the magnitude of the tension in the cable in units of kN? Answers (to choose from): D. 153.4 A. 93.3 B. 110.2 C. 130.2 OA

A body is loaded as shown in Figure 2 where P 80 kN and Q = 3 kN. In addition, the following information is known X1 = 2 m X2 = 2 m Y1 = 3 m Z1 = 3 m 22 3 m In the question that follows, select the answer that is closest to the true value. What is the magnitude of the tension in the cable in units of kN? Answers (to choose from): D. 153.4 A. 93.3 B. 110.2 C. 130.2 OA

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem for W = 1.0 lb. h = 12 in.,and k =0.511,/in.
Please show complete solution with formula and free body diagramA rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A closely coiled helical spring is made of 10 mm diameter steel wire, the mean diameter of the coil is 68.4 mm and there are 8 coils. Taking the modulus of rigidity as 100 kN/mm2, (a) find the stress in the wire, in N/m2, when carrying an axial load of 807N, (b) the deflection, in mm, and (c) the spring rate in N/mm. Express your answer in 3 decimal places.
Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces.If E = 210×103 N/mm2for steel, determine the change in its length.
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A concentric helical spring is used to support a load of 90 KN. The inner spring has arate of 495.8 KN/m and outside spring is 126.5 KN/m. If initially the inner spring is 25mm shorter than the outer spring, find the percent load carried by the inner spring. The correct answer is 76.81%. I just need the solution for this answer, thank you!
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.