A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33 in the textbook of Shigley's Mechanical Engineering Design, 8th Edition) (a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt? (b) What is the length of the grip I? (c) What is the height H of the nut? (d) Is the bolt long enough? If not, round to the next larger preferred length. (e) What is the length of the shank and the threaded portions of the bolt within the grip?

A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33 in the textbook of Shigley's Mechanical Engineering Design, 8th Edition) (a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt? (b) What is the length of the grip I? (c) What is the height H of the nut? (d) Is the bolt long enough? If not, round to the next larger preferred length. (e) What is the length of the shank and the threaded portions of the bolt within the grip?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: B. If a steel bolt is tested in single shear and fails at a load of 25 kips, at what load would we…

A: single shear force, F=25 kips

Q: lf-locking? b. What is the highest torque necessary to raise the load? c. What maximum torque is…

Q: 3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box…

Q: OAK Oes = Voe? + 3. T,² < S Oeş 0010 Calculate the factor of safety when preloading an M20 (6.6)…

Q: Required information For a bolted assembly with 19 bolts, the stiffness of each bolt is kh= 1.0…

Q: Design a toggle jack to lift a load of 5 kN. The jack is to be so designed that the distance between…

A: Hi, I have worked very hard to provide you with this solution, please UPVOTE this answer, thanks!!…

Q: What is a free body diagram? Draw and explain the free body diagrams of all the members of a four…

A: The answer is in the following steps

Q: Design a cast iron type flange coupling to transmit 15 kW at 900 rpm from an electric motor to a…

Q: A permanent bolted joint has four M24 ISO 8.8 bolts with coarse threads. The joint stiffness…

A: Answer: 136mm Solution is given below.

Q: (7) The cylinder head of a 10"x18" refrigerant compressor is attached by 10 stud bolts made of SAE…

A: Given: Let us consider the given, Cylinder pressure=350 psi Area of the cylinder head,A=10ιι×18ιι…

Q: A flange coupling is to be designed, using 30 mm diameter bolts at a distance of 160 mm from the…

Q: Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a…

A: Steel plates of size 14 in × 8 in of A 36 steel Ultimate tensile strength of A 36 steel is…

Q: 1) In a single threaded square thread screw, the input power is 3 kW and the speed is 1 rpm. Screw…

A: Given dataInput power to square thread Pin = 3kWSpeed N = 1rpsDiameter of the screw thread…

Q: Use table AT-7 , Faires A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for…

Q: 3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The…

A: The standard dimension of the nut and bolt are: Washer size:

Q: Assuming a minimum design factor = 2.00, Design the bolted cover of pressure vessel; determine the…

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit Power19 kW…

A: Given, P=19KW = 19×103W N=300rpm Service factor =1.35 τs=τb=τk=40Mpa =40N/mm2…

Q: What minimum thickness of the steel band can be used without exceeding a flexural stress of 320

Q: How many bolts are required for LRFD and ASD for the bearing-type connection shown, if PD = 50 k and…

Q: A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the…

Q: Figure 3.1 shows that an M10 x 1.5 of class 8.8 steel bolt clamps two metal plates, one aluminium…

Q: ind the work to be done in drawing the coaches together a distance of 200 mm against a steady load…

A: Pitch, P=10 mm=0.01 m,Mean Diamter, D=30 mm=0.03 mThreads are single start type,Coefficient of…

Q: Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size.

Q: The questions is this: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for…

A: Given DataFe=5000lbB1113 are using Using the table Screw and fastening

Q: (12) A turnbuckle connects two rods having %-16 UNC threads. The thread friction is 0.2. How much…

A: Write the given data. μ=0.2P=500 lbdm=0.335 in

Q: 3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box…

A: A flange compressive coupling is used to connect a driving electric motor to a reduction gear box of…

Q: The figure shows a schematic drawing of a vehicular jack that is to be designed to support a maximum…

Q: Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting P 32…

Q: Q4. Two plates have a length (L) and thickness (t), were welded together. Assume these plates have…

A: Q4: Weld joint: A weld joint is a joint which is used to join two or more plates by adding a fusion…

Q: In a bolted joint two smooth members are connected with an axial tightening force of 2200 N. If the…

Q: 1. For a bolted assembly with six bolts, the stiffness of each bolt is k» = 3 Mlbf/in and the…

A: Stiffness of each bolt, kb=3Mlbf/in Stiffness of each members, km=12 Mlbf/in per bolt External load,…

Q: : Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in…

Q: Rolling contact Pin in slot

A: Given:- To Find :- Degree of freedom (DOF)

Q: Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter…

A: To design: The clamp coupling. Given: The shaft diameter is d=60 mm. The torsional moment is T=160…

Q: 41. In a bolted joint two members are connected with an axial tightening force of 2200 N. If the…

A: Given that, We know two members are connected in bolted joint W=2200N, p=4 mm=0.004

Q: Find the number of bolts Mg*2 which made from SAE Grade 4 steel that should be used to provide a…

A: The maximum tensile force that may be given to a bolt without causing plastic deformation is known…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2 -…

A: Any action that can change the state of motion is force. Force is described by its magnitude, point…

Q: A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in…

Q: A M16 x 2 hex-head bolt with to clamp together two 25-mm thick steel plates. a nut is used

A: GivenM16×2 hex-head boltt=25 mm

Q: The figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 x2-C,…

Q: A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of…

Q: The area of American, UNC bolt is 0.61i .in2 with pitch of 5mm. A. What is the bolt nominal…

Q: A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The…

A: Given Data Coupling is rigid Bolt circular diameter, D=30 in Torque, T=18000 lb-in Yield strength,…

Q: Required information For a bolted assembly with 19 bolts, the stiffness of each bolt is kh= 1.0…

Concept explainers

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.

Question

100%

A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer
to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33
in the textbook of Shigley's Mechanical Engineering Design, 8th Edition)
(a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt?
(b) What is the length of the grip l?
(c) What is the height H of the nut?
(d) Is the bolt long enough? If not, round to the next larger preferred length.
(e) What is the length of the shank and the threaded portions of the bolt within the grip?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: (a)Calculating The length of the Thread LT for this Diameter Metric Coarse-Pitch Series Bolt

VIEW

Step 3: (b) Calculating The Length of The Grip I

VIEW

Step 4: (c) Calculating The height H of the nut

VIEW

Step 5:(d) Calculating the bolt long enough or not . Round to the next larger preferred length.

VIEW

Step 6:(e)Calculating The Length of the Shank and the Threaded Portions of the Bolt Within the Grip

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
a single-start, square-threaded power screw with the following parameters: PARTS A - D circle final answers for each part A - A weight of 1500 N must be lifted. What is the total required torque necessary to lift this weight? Give your answer in units of N m. Part B - if the available power to drive the screw is 1,011 Watts, determine the fastest speed at which the weight can rise. Give your answer in units of mm/s, Part C - The efficiency of the preceding power screw (expressed as a number between 0 and 1, not as a percentage) is ? Part D - Suppose a high-quality thrust bearing was used to eliminate the collar friction. The efficiency of the screw would now be?
QUESTION: Suppose a bolted tension used in a doube-D ring configuration is properly preloaded. The spring constant for the bolts is 7.8 MN/m and the spring constant for the members is 12.7 MN/m. By how much does the tensile force in the bolt increase when a load of 705 N is applied? You may assume that joint separation does not occur. Give your answer in units of N
How many bolts are required for LRFD and ASD for the bearing-type connection shown, if PD = 50 k and PL = 100 k? A325 3/4 in bolts, threads excluded from shear plane.
Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter of 60 mm. The torsional moment to be transmitted by this coupling taking in to account over loading as 160 N-m. The number of bolts used are 6 and the allowable stress in the material of the bolt is limited to 5N / m * m ^ 2 . The coefficient of friction between the shaft and muff material is 0.25.
Question No.16: A double threaded power screw with ISO metric trapezoidal threads with 15° semi-angle of thread is used to raise a load of 300 kN. The nominal diameter is 100 mm and pitch is 12 mm. the coefficient of friction at screw threads is 0.15. Neglecting collar friction, calculate; (i) torque required to raise the load, (ii) torque required to lower the load and (iii) efficiency of the screw.
Don't attempt wrong .Downvoted for that...A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
Bolt properties: M12 x1.75 ISO 5.8(a) Determine a suitable length for thebolt, use preferred size.(b) Determine the bolt stiffness.(c) Determine the stiffness of themembers.
Design of the Screw Jack. Lifting load – W, kN is 70. Hight of lifting– H, mm is 500 Types of threads is Square Material of nut is Cast iron
Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in lb-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?
A 1/2-in-dia UNC, class 2 bolt with rolled threads is preloaded to 80% of its proof strength when clamping a 3-in-thick sandwich of solid steel. A static 1000-lb external load is applied. Part A Find the safety factor against static yielding. Express your answer using three significant figures. Part B Find the safety factor against joint separation. Express your answer using three significant figures.