A boost chopper is powered by a 24-V dc power supply. What is the output voltage range of this chopper if the duty cycle varies between 20 and 95%? also, A buck chopper is powered by a 200-V dc power supply. What is the output voltage range of this chopper if the duty cycle can be varied between 30 and 95%

A boost chopper is powered by a 24-V dc power supply. What is the output voltage range of this chopper if the duty cycle varies between 20 and 95%? also, A buck chopper is powered by a 200-V dc power supply. What is the output voltage range of this chopper if the duty cycle can be varied between 30 and 95%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A boost chopper is powered by a 12-V dc power supply. What is the output voltage range of this chopper if the duty cycle can vary between 20 and 95%?
What is the differential compound generator and what is the principle of work, what are its advantages and disadvantages, and what is its drawing and image
(i) A chopper circuit drives an inductive load from 298 V DC supply. Given the load resistance as 5.5 Ω, the average load current as 37.5 A and operating frequency is 400 Hz. Calculate the ON period and OFF period of the chopper in milliseconds. Also determine the duty cycle of the chopper. (ii) Draw the output voltage for the above condition and label its ON period and OFF period. Duty Cycle ON period OFF period
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
A DC chopper is used in regenerative braking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continuous and ripple free. What is the value of power feedback to the supply ?
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
Answe completely and elaborate complete details. No plagiarism 1.) Define the working principle of AC Motor.2.) Define the different types of AC Motor.
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
Power Electronics a) A Flyback Converter with an ideal turns ratio of 1: 1 feeds a 10 Ohm load resistance with a voltage of 10 Volts. Calculate the welding voltage since duty ratio is given as D = 0.2. b) A Flyback Converter with ideal turns ratio of 1: 1 feeds a load resistance of 5 Ohm with a voltage of 40 Volts. If the welding voltage is 30 Volts, calculate the D coefficient, which gives the relationship between the output voltage and the welding voltage.
A 3-phase full converter is delivering a constant load current of 50 amps at 230 Volt DC when its input is 3-phaser, 415 Volt, 50 Hertz. If each thyristor has a voltage drop of 1.1 Volt when conducting, calculate (a) The firing angle delay (b) RMS current of SCRs (c) RMS source currents (d) The power loss in each SCR.(e) Input power factor.
A four-pole induction motor drives a load at 2405 rpm. This is to be accomplished by using an electronic converter to convert a 400V dc source into a set of three-phase ac voltages. a) Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2hp. b) If the dc-to-ac converter has a power efficiency of 93 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.