A box rests on a flat surface. The normal reaction of the surface on the box is 6N and the coefficient of static friction between the box and the surface is 0.14. A horizontal force is applied to the box so that it is on the point of slipping. To 2 significant figures, what is the magnitude of the horizontal force in Newtons? ● ● 0.023 0.84 1.4 8.2 43

A box rests on a flat surface. The normal reaction of the surface on the box is 6N and the coefficient of static friction between the box and the surface is 0.14. A horizontal force is applied to the box so that it is on the point of slipping. To 2 significant figures, what is the magnitude of the horizontal force in Newtons? ● ● 0.023 0.84 1.4 8.2 43

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter5: Newton's Laws Of Motion

Section: Chapter Questions

Problem 76PQ: Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to...

See similar textbooks

Similar questions

A block of mass M = 10 kg is sitting on a surface inclined at angle θ = 45°. Given that the coefficient of static friction is μs = 0.5 between block and surface, what is the minimum force F necessary to prevent slipping? What is the maximum force F that can be exerted without causing the block to slip?
A block weighs 100. N and rests on a horizontal surface. If Ms = 0.50 and uk = 0.20 between the block and the horizontal surface, then (a) What is the magnitude of the frictional force acting on the block? Justify your What is the magnitude of the frictional force acting on the block if a horizontal force of 35.0 N is now used to push the block? Justify your answer with a calculation. What is the magnitude of the minimum horizontally applied force that will start the block sliding? Justify your answer with a calculation. If the magnitude of the applied horizontal force on the block is 55.0 N, what is the magnitude of the frictional force acting on the block? Justify your answer with a calculation.
The two blocks (m= 16 kg and M = 88 kg) are not attached to each other.The coefficient of static friction between the blocks is ms =0.38, but the surface beneath the larger block is frictionless. What is the minimum magnitude of the horizontal force required to keep the smaller block from slipping down the larger block?
In the wheelbarrow, the load has a perpendicular lever arm of 7.50 cm, while the hands have a perpendicular lever arm of 1.02 m. (a) What upward force must you exert to support the wheelbarrow and its load if their combined mass is 45.0 kg? (b) What force does the wheelbarrow exert on the ground?
Two masses mA =9.3kg and mB=6.1kg are on inclines and are connected together by a string as shown in the figure. The angles theta subscript A=700 and theta subscript B = 360 . In the absence of the friction, the force F is required to pull the masses at a constant velocity up the fixed inclines. The force F is now removed. What is the magnitude of the acceleration of the two blocks? Take g =9.81 m/s2, and express your answer using two decimal places.
If you hang a car with a mass of 1770 kg from a steel beam, you observe that the beam bends 0.095 degrees. What is the tension in this beam, in newtons? Using the equation T=F/(2*sin(theta))
The two blocks (m =16 kg, M =88 kg) in Fig. are not attached to each other. The coefficient of static friction between the blocks is µs =0.38, but the surface beneath the larger block is frictionless. What is the minimum magnitude of the horizontal force required to keep the smaller block from slipping down the larger block?
The figure shows a person whose weight is W = 782 N doing push-ups. Find the normal force exerted by the floor on (a) each hand and (b) each foot, assuming that the person holds this position.
A mass M of 10 kg hangs from three wires as shown in Figure. If the system is in equilibrium, find the tensions in the wire-1 and wire-2 if α=30o and β=53o . cos30o =sin60o=0.866 cos60o =sin30o=0.500 sin53o=cos37o=0.8 sin37o=cos53o=0.6 g=9.8 m/s2
What is the magnitude of the static friction force required to keep a 2.00 kg block resting on an inclined plane at an angle 25 degrees? If the angle was increased, such that the incline plane was steeper, would the magnitude of the static friction force required to hold the block at rest increase, decrease, or stay the same?
There are two forces on the 1.19 kg box in the overhead view of the figure but only one is shown. For F1 = 15.7 N, a = 14.7 m/s2, and θ = 34.1°, find the second force (a) in unit-vector notation and as (b) a magnitude and (c) a direction. (State the direction as a negative angle measured from the +x direction.)
Two blocks, with masses m=3.6 kg and M=7.1 kg, are connected by a lightweight wire that's shown in the picture. The incline makes an angle of 55 degrees with the horizontal and the coefficient of friction between each block and the surface is 0.200. Find a) the acceleration of the blocks and b) the tension in the string.