A bridge consists of the following elements as : Arm AB: A choke coil having a resistance R, and inductance L₁ Arm BC: A non-inductive resistance R, Arm CD: A capacitor C₁ in series with a non-inductive resistance R₁. Arm DA: A non-inductive resistance R₂. When this bridge is supplied from a 500 Hz supply source, balance is obtained under following conditions: R₂ = 2400 Ω; R = 750 Ω R₁ = 64.5 2; C4 = 0.35 µF The series resistance of capacitor is = 0.4 2. Determine the resistance and inductance of the choke coil; if supply is connected between A and C and the detector is between B and D.

A bridge consists of the following elements as : Arm AB: A choke coil having a resistance R, and inductance L₁ Arm BC: A non-inductive resistance R, Arm CD: A capacitor C₁ in series with a non-inductive resistance R₁. Arm DA: A non-inductive resistance R₂. When this bridge is supplied from a 500 Hz supply source, balance is obtained under following conditions: R₂ = 2400 Ω; R = 750 Ω R₁ = 64.5 2; C4 = 0.35 µF The series resistance of capacitor is = 0.4 2. Determine the resistance and inductance of the choke coil; if supply is connected between A and C and the detector is between B and D.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Similar questions

1- A tank contains 2.0 kg of Water at a temperature 120°C and volume 0.2 m3 . Find: phase, pressure and quality of water. 2- Determine the specific volume for R-410a at 100°C, 3.0 MPa using the following models: a) The R-134a tables, b) Ideal Gas, c) Generalized Compressibility Chart
The AC Bridge shown below is used to measure an unknown inductance, Lx and its internal resistance, Rx. The Bridge parameters are R1 = 20,000 ohms, R2 = 50,000 ohms, C2 = 0.003 μf, ω= 105 radians per sec. C1 is adjustable from 10 pf to 150 pf, and R3 is adjustable from 0 to 10,000 ohms. At Balance,I. Derive expressions for Rx and Lx in terms of ω, R1, R2, R3, C1, and C2.II. Determine the largest values of Rx and Lx that are measurable with the given parameters.
The following parameters are used in an EDM process, the supply voltage is 150V. The resistance and capacitance in the circuit are 50 Ohms and 15 microfarads respectively. The tool is made of brass and kerosene is used as the dielectric. A hole diameter of 20 mm is to be cut into a plate of thickness of 3mm. If the discharge takes place at maximum power conditions. The value of constant K4=0.18, calculate the MRR, and machining time.
The AC Bridge shown below is used to measure an unknown inductance, Lx and its internal resistance, Rx. The Bridge parameters are R1 = 20,000 ohms, R2 = 50,000 ohms, C2 = 0.003 µf, w = 105 radians per sec. C1 is adjustable from 10 pf to 150 pf, and R3 is adjustable from 0 to 10,000 ohms. At Balance, I. Derive expressions for Rx and Lx in terms of w, R1, R2, R3, C1, and C2. II. Determine the largest values of Rx and Lx that are measurable with the given parameters.
A closed loop system with G(s) = k / [ (s+3)(s+4)(s+12) ] has its dominant poles placed so the ratio of the imaginary to real parts is -1.423. If the value of the real part is -3.3, what is the angle of the system. Draw the Root Locus showing all important points/data
Short Problem: Given a parallel RLC circuit comprised of the following element: 55.27-ohm resistor, ideal inductor with reactance of 33.87 ohms; and a capacitor with reactance of 14.68 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.
Short Problem: Given a parallel RLC circuit comprised of the following element: 97.19-ohm resistor, ideal inductor with reactance of 36.14 ohms; and a capacitor with reactance of 16.25 ohms. Compute for true power in watts given an ac voltage source of 100 cis 0 volts. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.
V1 = 40∠10 ° V2 = 50∠35 ° R = 45 Ω XL = 45 Ω XC = 40 Ω Zload = 10 Ω Using Thevenin Theorem, search for : i. voltage drop across the load ii. Load current, ILOAD. iii. Voltage, VXL and current, IXL of inductor, XL. iv. Voltage, VXC and current, IXC of capacitor, XC. v. Time domain representation of load voltage and load current. vi. Time domain representation of voltage and current, for capacitor and inductor. vii. The sinusoidal waveforms for part (v) and (vi) viii. The value of load, ZMAX that shall replace the existing load in order to get maximum average power transfer. ix. Calculate the maximum average power that will be transferred to load when load is replaced with ZMAX
A current of 5A flows in a resistor of 2 ohms. 18 kJ is the energy dissipated in 300 seconds in the resistor. True/False Linear Circuit is the one whose parameters are not constant. True/False Choke is used to limiting the current flowing through it. True/False In an Inductive circuit, relationship between inductance (L) is directly proportional to the inductive reactance (XL). True/False
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
Figure a shows the ignition circuit of an automobile system. It consists of four Resistors R, as well as the energy storing elements of Inductor and Capacitor . Meanwhile Figure b shows the equivalent circuit of the same system of Figure a. Let Z1 and Z2 be the Impedances seen from the respective terminals. The variables and are the mesh currents flowing in the loops 1 and 2, respectively. Let the values of Resistors are 2, while the value of the Capacitor and Inductor are 1. i) The total impedance of Z1=ii) The total impedance of Z2=iii) Current I2(S) in function of Vs(S) = iv} Find the transfer function of Vz2(S)/Vs(S) =
A 3-ph, 50 Hz, 150 km length O.H.T.L. supplies a load with P MW load at 0.80 lag P.f. and 110 kV where P=24 This T.L has a resistance of 0.11 Ω/km and an inductance per phase of 1.65 mH/ km and a shunt capacitive reactance per phase of 0.333 MΩ.km. Using nominal T circuit, Find: 1- Constants A, B, C, and D. 2- Voltage drop across this T.L. 3- Transmission line efficiency. 4- The loadability of transmission line (approximate calculations). 5- Suggest a way to decrease the voltage drop to 40% of its value calculated in point 2. Verify your answer. 6- Suggest a way to increase the loadability to double of the value calculated in point 4. Verify your answer. 7- Wave length and velocity of propagation across this transmission line.