a) Calculate the resistances R1, R2, RS and RD so that ID E [0.4, 0.8]mA, Zi = 400K and that VDS is 5V away from the border with the ohmic region in the worst case. b) Calculate the range of voltage gains of the amplifier. 10K N Z₁ R₁ ΤΩ www VDD = 24v www Ro T1 MPF102 Rs Col HH HH Cs l Vo RL 10K 17 Zo

a) Calculate the resistances R1, R2, RS and RD so that ID E [0.4, 0.8]mA, Zi = 400K and that VDS is 5V away from the border with the ohmic region in the worst case. b) Calculate the range of voltage gains of the amplifier. 10K N Z₁ R₁ ΤΩ www VDD = 24v www Ro T1 MPF102 Rs Col HH HH Cs l Vo RL 10K 17 Zo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the output current and output resistance of the current source as shown if VDD = 10 V, R4 = 2 MΩ, R3 = 1 MΩ, RS = 120 kΩ, Kp = 750 μA/V2, VT P = −0.75 V, and λ = 0.01 V−1?
Find the differential-mode voltage gain, CMRR, input resistance, and output resistance for the amplifier as shown if VCC = 15 V, VEE = 15 V, VA3 = 75 V, βo1 = βo2 = βo3 = βo4 = 100, I1 = 100 μA, I2 = 500 μA, I3 = 5 mA, R1 = 750 kΩ, and RL = 2 kΩ. Assume R2 and R3 =∞.
For the amplifier as shown, VCC = 7.5 V, VEE = 7.5 V, βF = 100, IEE = 20 μA, and RC = 180 kΩ. (a) What are the output voltages υo and Vo for the amplifier for υi = 0 V and υi = 2 mV? (b) What is the maximum value of υi ?
(a) What is the gain of the circuitas shown ifAv = vo/(v1 − v2) and R = 10 k ? (b) What is theinput resistance presented to v2? (c) What is the inputresistance at terminal v1? (d) What is the outputvoltage if v1 = 3 V and v2 = 1.5 cos 8300πt V?(e) What is the output voltage if v1 = [3 −1.5 cos 8300πt] V and v2 = 1.5 sin 8300πt V?
What is the voltage gain of the amplifier shown if VCC = VEE = 5 V, I1 = 500 μA, R1 = 20 Mμ, I2 = 100 μA, R2 = 10 Mμ, βo = 80, VA = 75 V, Kp = 5 mA/V2, and VT P = −1 V?
In the adjacent figure R1 = 56kΩ, R2 = 45kΩ, R3 = 138 kΩ and V supply = 12V. If the bridge is in balance (VA=VB) at 20°C, calculate, 1) the resistance of the RTD at 20°C; 2) the resistance of the RTD at 70°C; 3) the voltage difference on the inputs of the differential amplifier if the RTD is at 70°C. (α20 = 0.00392Ω/°C)
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
Design For the design of the amplifiers, consider a very large load resistance RL. Use a 15 V DC source and a sinusoidal input signal of 200 mVpp and 1 kHz. Design a voltage amplification stage with a common emitter amplifier thatmeet the following specifications: Voltage gain of 15 (Av2 ≅ 15) Input impedance greater than or equal to 10 times Zo1 (Zi2 ≥ 10 Zo1). Low cut frequency less than or equal to 20 Hz (fcb2 ≤ 20 Hz). Maximum symmetric excursion. Use a 2N2222A (NTE123A) transistor. Also, determine the value of the impedance output (Zo2) of the designed circuit.
Question 1: Draw and explain the transistor amplifier, which is usually referred as emitter follower.Also, (i) derive its voltage and current gains by equivalent circuit; (ii) compare its voltage and current gains with other transistor amplifiers. Question 2:(a) Predict the name of the curve drawn between ID and VGS of the JFET and represent the cut off voltage in it. (b) E-MOSFET has ID(on) = 600mA (minimum) at VGS = 9V and VGS(th) = 1 V. Find the drain current for VGS = 6 V. Question 3: (a) State the name of the power amplifier, which has a efficiency as 10% in practical case and also derive and prove its theoretical efficiency is 25%. (b) Explain the role of Q point in power amplifiers based on its location in AC load line.…
Draw the dc equivalent circuit and find the Qpoint for the amplifier shown . Assume Kn = 500μA/V2, VT N = −2V, VDD = 18V, RI = 2kΩ,R1 = 6.2 kΩ, RD = 7.5 kΩ, and R3 = 51 kΩ.
What are the gain Av, input resistance, and output resistance of the three stage amplifier as shown (a) if R2 = 68 kΩ and R1 = 2.7 kΩ?
Design a linear amplifier, based on a bipolar junction transistor 2N3904 in common emitter configuration. The supply voltage is 28V. The quiescent operating collector current for the amplifier should be around 10mA. The data sheet for the transistor shows that the DC current gain at this operating current is about 200. Draw the circuit diagram of your design. Label all the components in the circuit. Show all the voltages and currents that you use for calculations in your design. Label them using consistent naming convention.