A cantilever beam BD rests on a simple beam AC as shown below. Both beams are of the same material and are 3 in wide by 8 in deep. If they jointly carry a load P=1400 lb, compute the maximum flexural stress developed in the beams in psi. Note: another load of 1400 lb is added at 2 feet from point B. No need to write the unit in your final answer. Use 2 decimal point. P = 1400 lb P=1400 lb 8 ft R₁ 4 ft 8 ft 12 ft C R₂

A cantilever beam BD rests on a simple beam AC as shown below. Both beams are of the same material and are 3 in wide by 8 in deep. If they jointly carry a load P=1400 lb, compute the maximum flexural stress developed in the beams in psi. Note: another load of 1400 lb is added at 2 feet from point B. No need to write the unit in your final answer. Use 2 decimal point. P = 1400 lb P=1400 lb 8 ft R₁ 4 ft 8 ft 12 ft C R₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
Find EIδ under each concentrated load. Find EIδ under 200lb load and EIδ under 400lb load.
Compute using Euler's formula: A square aluminum bar is to support a load of 65kN on a length of 4.50 m. Assume pinned ends, Determine the length of each side E = 70 GPa.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
A simply supported beam is used to carry the uniformly distributed load of magnitude 3 W and the concentrated load W. What is the maximum allowable value of W if the working stress in bending is 122 MPa? b = 180; d = 318 Round your answers to 2 decimal places.
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.56 in from the top of the beam on section 2.06 feet to the right of B if P = 1083 lb, Q = 4176 lb, w = 0.88 in, L = 8.52 in, b = 3.84 in, and h = 0.7 in. Round off the final answer to two decimal places.
The reinforced concrete beam has the cross-sectional area shown in the figure with b =12 in., d=16 in., ? steel= 1.571 in.2, determine the largest bending moment that may be applied safely. Takethe elastic moduli ?steel=29(10^3) ksi and ?concrete= 3.6(10^3) ksi. The working stresses are2.39ksi for concrete and 22.145ksi for steel.
Joists support a floor and transfer their load to beams at each end of each joist. Joists are 2 ft on center and 30 ft long. If w, the load on the floor, is uniformly distributed and is 30 lb/ft2, what is the load on one joist? If the maximum flexural stress S in a joist is given by S = M/Z, where M is the maximum bending moment (pound-foot) and Z is the section modulus (cubic inches), what is the stress in a joist that has a section modulus of 50 in.3 and is 30 ft long? Assume that the maximum bending moment for a simply loaded joist is given by M = wL2/8, If the joists are made of pine, which has an allowable bending stress of 9,300 lb/in.2, will it carry the load?
The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determine the largest load P (kips) that can be applied at C if the stress in the steel rod is limited to 24 ksi and the vertical movement of end C must not exceed 0.15 in. Where L1 = 2.2 ft and L2 = 3.2 ft. Your final answer should have two decimal places
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a uniform load equal to 12 KN/m. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places, no need for unit) with diagram and complete solution