Problem Sets - 1: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w, as shown in the figure. a) Determine the largest allowable value of wo if the working stress in bending is 100 MPa. b) Determine the maximum shear stress in the beam Wo 200mm A -195mm 1.2m B 2.4m

Problem Sets - 1: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w, as shown in the figure. a) Determine the largest allowable value of wo if the working stress in bending is 100 MPa. b) Determine the maximum shear stress in the beam Wo 200mm A -195mm 1.2m B 2.4m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

H1. A rectangular beam of 100mm wide and 150mm deep is subjected to Shear force of 30KN, Determine ratio of Maximum shear stress to Average shear stress. Derive the equation which is used to find out the shear stress.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
For the beam in figure: 1. Compute the maximum shearing stress devloped in the beam. 2. Determine the shear stress in a fiber located at y1 = 26 mm , from the bottom for section 2 m from the left end of the beam.
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
In Figure 2, the system under the torsional effect;Draw the torsional moment diagram.Determine the torsional angle CA (rotation angle) that will occur at point C.Determine the maximum shear stress that will occur in the system.(G=80 000 MPa)M1(Nm) 9000 M2(Nm)2000 D1(mm) 90 D2(mm) 60 D3(mm) 50 D4(mm) 30
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
A propped cantilever beam of length ? = 1 m, with an inner hinge at point B, carries a uniformly distributed load ?, as shown in Figure Q1 (a). The beam is made from a circular hollow section with an inner radius of ?? = 5 cm and a thickness of ? = 2 cm (refer to Figure Q1 (b)). The maximum allowable longitudinal stress of the beam is 150 N/mm2.
A 5m diameter open cylindrical tank 12 m high contains water. It is made of steel 18mm thick. a) what is the maximum circumferential stress when its full of water? b) What is the longitudinal stress near the bottom when it's full of water? c) what depth of water will make the circumferential stress 10 MPa.
a vertical force of 60 KN acts on the cage system in the figure from point D. If the perpendicular cross-sectional area of the BC bar is 1000 mm2 and the perpendicular cross-sectional area of the other bars is 500 mm2, then E = 200 GPAa) find the total deformation energy of the cage systemb) find the vertical displacement of Point Dc) find the horizontal displacement of Point C.
If sY = 50 ksi, determine the factor of safety for this loading based on (a) the maximum shear stress theory and (b) the maximum distortion energy theory.