Answered: A cantilever beam with flexural…

A cantilever beam with flexural regidity of 200 N/m2 is loaded as shown in figure. Find the deflection at tip of the beam.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.7P: -5-7 A cantilever beam AB carries three equalaly spaced concentrated loads, as shown in the figure....

See similar textbooks

Related questions

Q: A cantilever beam AB is subjected to a concentrated load P and a couple MQ acting at the free end…

A: Given data as per question The concentrated load applied =P The couple applied =M0 θB=Area of MEI…

Q: An I-profile steel beam is supported and loaded as shown in the figure. If the mass of the block is…

A: E=200 GPa,I=17×106 mm4L=8 m or 8000 mmb=2000mmFor simply supported beam, deflection y is given…

Q: Derive the deflection at different points of the beam, as shown in the table. Use CONJUGATE BEAM…

Q: y E,I L A cantilever beam with distributed lateral load p as shown above. Given: The deflection and…

A: since there is only one element, the element matrix equation is same as global matrix equation,…

Q: a) A massless beam ABC of span L and con- staht nešural rigidity EI is simply supported at A and C,…

A: For solution refer below images.

Q: Homework; In Figure below, a cantilever beam is subjected to an inclined force (P); calculate: 1-…

Q: A beam of length 6m is supported at its ends and carries UDL 0f intensity 40KN/m as shown in fig.…

A: Note:-The length of beam AB is given as 6m. But the sum of AB,CD,DB is 8m. so we will…

Q: A beam of length 8m is supported at its ends and carries UDL 0f intensity 40 as shown in fig.…

A: Given Data, L= Length of the beam = 8m w= Intensity of UDL = 40 KN/m E= 2x105 MPa = 2x1011 N/m2 I =…

Q: Calculate the maximum shear stress Tmax and the maximum bending stress σmax in a simply supported…

A: Given data: The uniform load on the beam, w = 18 kN/m. The length of the beam, l = 1.75 m. The…

Q: A steel canthlever fAom a mefers Is loaded hith uniformly distributed . wall of 20 kN/m. Yun. Find…

Q: 9.3-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load…

A: Determine the deflection curve and find deflection at point B.

Q: b) A cantiliver beam ABC shown in Figure Q3(b) has a span length of L m carry a point load P at…

Q: middle of AB using the Castigliano me

Q: A simply supported beam hinged at A and supported at C, is carrying a distributed load and a point…

Q: 2 Find the equation of deflection (under the uniformly distributed load) and calculate the maximum…

Q: / The simply supported beam shown in Figure below has a central half of the beam enlarged, so that…

Q: If w = 25 kN/m., calculate the value of EIδ at 1 m. of the free end of the loaded beam as indicated…

Q: Compute the slope and deflection of the simply supported beam shown in figure Q2a. Assume value of E…

Q: A cantilever beam of length Lis subjected to a concentrated load Pat a distance of L/3 from the free…

A: Given Total length = L Concentrated load = P Load act at L/3 distance Find Deflection

Q: For the beam shown, use superposition and find a) maximum deflection in beam, and b) deflection at…

Q: Find the slope deflections using unit load method or any other method in the text book. For the beam…

Q: A cantilever beam AB of length L has a fixed support at A and a roller support at B (see figure).…

A: The total sum of reactions is zero as per equilibrium conditions RA + RB = 0 Since, RA is negative…

Q: Class A cantilever beam AB of circular cross section and length L=450 mm supports a load P-400 N…

Q: Find slope and deflection in beam at point C shown in figure below. Assume that modulus of…

A: Let :-∑Fy =…

Q: Question 2 The simply supported beam shown in Figure supports the triangular distributed loading.…

A: Draw the free-body diagram of the simply supported beam. Apply force equilibrium in a vertical…

Q: Read the question carefully and give me right solution with clear calculations. A cantilever beam…

Q: Q4/ By using Double - Integration Method, find the deflection and rotation at point (C) of the beam…

Q: 3. Find the angle of rotation BA at the left-hand, the deflection under the downward load, and the…

A: Calculated angles of rotation at point A .and deflection at load P and deflection at mid point of…

Q: A simply supported beam of 6 m length with external diameter 150 mm and thickness 15 mm has maximum…

A: Given data: The length of the beam is l=6 m=6000 mm The external diameter of the beam is D=150 mm…

Q: For the simply supported beam shown below find reactions at supports A a В. 2m 14KN 3m 28KN 2m B. D.

A: Let us draw the free body diagram Using the conditions of equilibrium ∑Fy=0RB+RD-14-28=0RB+RD=42KN

Q: A cantilever beam AB of length Land uniform flexural rigidity El has a bracket AC attached to its…

Q: A cantilever beam, 850 mm long, carries a uniform load of 5 kN/m. What is the value of Ely at the…

A: GIven: Cantilever beam w=5 kN/m L=850 mm TO determine: EIy at free end

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A: Given: Total length of a cantilever beam, l =5 m Beam is subjected to two uniformly distributed…

Q: 9.3-12Derive the equation of the deflection curve for a cantilever beam AB supporting a load P at…

Q: A simply supported beam of dimension 4m x 45mm x 90mm, which is subjected to a mid-point load of 130…

Q: Derive the equation of the deflection curvefor a cantilever beam AB supporting a load P at thefree…

A: Given Load = P Length = L Find Deflections

Q: Analyze the given beam that is subjected to a bending moment of 20 kg-m. Find the maximum stress…

A: An I section with unequal top and bottom width is given. And the bending moment acting on the beam…

Q: A propped cantilever steel beam is constructedfrom a W12 x 35 section. The beam isloaded by its…

A: Given data as per question Length of the beam =11.5 ft E = 30,000 ksi. For W12 x 35 section q =…

Q: For the simply supported beam shown below find reactions at supports A and В. 2m 14KN 3m 28KN 2m

Q: A cantilever beam AB supports a distributed load of peak intensity g. acting over one-half of the…

Q: What is the span length L (in ft) of a uniformly loaded, simple beam of wide-flange cross section…

A: Given : The maximum bending stress = 11400 psi The maximum deflection = 0.1 in The modulus of…

Q: A simply supported beam is loaded with apoint load, as shown in the figure. The beam is a steelwide…

A: Given data as per question P = 10 kips f L =10 ft a = 7 ft b = 3 ft

Q: Calculate the beam deflection at point C. E = 206.8 GPa, In = 1.873 x 10-6 m4. Use either the double…

Q: Mo Мо А В X+ L

A: A beam is defined as a structural member subjected to transverse shear load during its…

Q: n curve at th

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Determine the deflection of beam from the given fig.

A cantilever beam with flexural regidity of 200 N/m2 is loaded as shown in figure. Find the
deflection at tip of the beam.
500N
50mm.
100mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Obtain a formula for the ratio c/maxof the deflection at the midpoint to the maximum deflection for a simple beam supporting a concentrated load P (see figure). From the formula, plot a graph of c/max versus the ratio a/L that defines the position of the load (0.5 < a/L < ) What conclusion do you draw from the graph? (Use the formulas of Example 9-3.)
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
The deflection curve for a cantilever beam AB (see figure) is given by v=q0x2360L2EI(45L440L3x+15L2x2x4) Describe the load acting on the beam. Determine the reactions RAand M 4at the support.
Obtain formulas for the angle of rotation 0Aat support A and the deflection SajAXat the midpoint for a simple beam AB with a uniform load of intensity q (see figure).
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.
A cantilever beam of a length L = 2.5 ft has a rectangular cross section {b = 4in,, h = Sin,) and modulus E = 10,000 ksi. The beam is subjected to a linearly varying distributed load with a peak intensity qQ= 900 lb/ft. Use the method of superposition and Cases 1 and 9 in Table H-l to calculate the deflection and rotation at B.
A simply supported beam (E = 1600 ksi) is loaded by a triangular distributed load from A to C(see figure). The load has a peak intensity q0= 10 lb/ ft, and the deflection is known to be 0.01 in, at point C. The length of the beam is 12 ft, and the ratio of the height to the width of the cross section is (h:b) 2:1, Find the height h; and width h of the cross section of the beam.
-6 Calculate the maximum deflection of a uniformly loaded simple beam if the span length L = 2.0 m, the intensity of the uniform load q = 2.0 kN/m, and the maximum bending stress = 60 MPa, The cross section of the beam is square, and the material is aluminum having modulus of elasticity E = 70 GPa. (Use the formulas of Example 9-1.)
A cantilever beam has two triangular loads as shown in the figure. Find an expression for beam deflection Scusing Superposition. Find the required magnitude of load intensity q2in terms of q0so that the deflection at C is zero. Find an expression for the deflection at C if both load intensities, qxand q2, are equal to q0.
A simple beam ABC has a moment of inertia 1,5 from A to B and A from B to C (see figure). A concentrated load P acts at point B. Obtain the equations of the deflection curves for both parts of the beam. From the equations, determine the angles of rotation 0Aand Bcat the supports and the deflection 6Bat point B.
-12 Determine the angle of rotation Band deflection Bat the free end of a cantilever beam AB having a uniform load of intensity q acting over the middle third of its length (see figure).
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.