A car weighting 10,000 N supported by a hydraulic car lift. The large piston supporting the car has a diameter of 25.4 cm, while the small piston has a diameter of 2.54 cm. How much force must be exert on the small piston to ?support the car 10 N O 14.1 N O 141 N O 100 N O

A car weighting 10,000 N supported by a hydraulic car lift. The large piston supporting the car has a diameter of 25.4 cm, while the small piston has a diameter of 2.54 cm. How much force must be exert on the small piston to ?support the car 10 N O 14.1 N O 141 N O 100 N O

Name: A car weighting 10,000 N supportedby a hydraulic car lift. The large
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: A car weighting 10,000 N supportedby a hydraulic car lift. The large pistonsupporting the car has a diameter of25.4 cm, while the small piston has adiameter of 2.54 cm. How much forcemust be exert on the small piston to?support the car10 N O14.1 N O

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 43PQ

See similar textbooks

Similar questions

Water is moving at a velocity of 2.00 m/s through a hose with internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
A man has a mass of 80 kg and a density of 955kg/m3 (excluding the air in his lungs). (a) Calculate his volume. (b) Find the buoyant force air exerts on him. (c) What the ratio of the buoyant force to his weight?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
What is density of a woman floats in fresh water with 4.00% of her volume above the surface? (This could be measured by placing her in a Wii marks on the side to measure how much water she displaces when floating and when held under water.) (b) What percent of her volume is above surface when she floats in seawater?
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
A large storage tank with an open top is filled to a height h0. The tank is punctured at a height h above the bottom of the tank (Fig. P15.39). Find an expression for how far from the tank the exiting stream lands. Figure P15.39
The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
An oil gusher shoots crude 25.0 m the through a pipe with a 0.100-m diameter. Neglecting resistance but not resistance of the pipe, and assuming laminar flow, calculate pressure at be entrance of be 50.0-m-Iong vertical pipe. Take of the oil to be 900 kg/m3 and its viscosity to be 100(N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to 50.0-m column of oil in pipe.