A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1. The G value of carbon steel is 80 GPa. The outer diameter of the shaft is 40 mm. Shaft AC and shaft DB are hollow with inner diameter of 20 mm, while shaft CD is solid. 300 N-m 500 N-m 200 N-m 400 N-m 300 mm 400 mm 500 mm Figure 1. a) For each section of the shafts, determine the maximum shearing stress. b) For each gear, determine its angle of twist. c) Determine the angle of twist of end B with respect to A

A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1. The G value of carbon steel is 80 GPa. The outer diameter of the shaft is 40 mm. Shaft AC and shaft DB are hollow with inner diameter of 20 mm, while shaft CD is solid. 300 N-m 500 N-m 200 N-m 400 N-m 300 mm 400 mm 500 mm Figure 1. a) For each section of the shafts, determine the maximum shearing stress. b) For each gear, determine its angle of twist. c) Determine the angle of twist of end B with respect to A

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollowwith inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CDare solid with diameter d. Given the torque at A, B, C and D is 6 kNm, 14 kNm, 26 kNmand 6 kNm, respectively.a) Determine the maximum and minimum shearing stress in shaft BC. b) Calculate the required diameter, d of shafts AB and CD if the allowable shearingstress in these shafts is 65 MPa.
In the geared shaft shown below, gears A and B and gears C and D are separated by 500 mm. Gears B and C are separated by 400 mm. Gear A is experiencing a 250N⋅m250N⋅m clockwise torque; gear B is experiencing a 75N⋅m75N⋅m counter-clockwise torque; gear C is experiencing a 325N⋅m325N⋅m counter-clockwise torque; and gear D is experiencing a 150N⋅m150N⋅m clockwise torque. What is the absolute maximum shear stress in the shaft (in MPa) if the shaft has a 50-mm diameter?
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
A hollow shaft is to transmit 390 kW at 70 rpm. If the shear stress is not to exceed 45 MPa and the diameter ratio is 0.58, Design the shaft by assuming the maximum torque is 40% greater than its mean torque. (i) The mean torque is (Unit is in Nm)= (ii) The maximum torque is (Unit is in Nm iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm
The intermediate shaft of a two-stage gearbox is given in the figure. P = 4 kW power is transmitted at n = 150 rpm with the help of two helical gears on the shaft.The forces acting on the gears are given as Ft1 = 5092 N, Fr1 = 1972 N, Fa1 = 1853 N, Ft2 = 2546 N, Fr2 = 986 N, Fa2 = 926 N. Diameter of small helical gear d1 = 100 mm, largethe diameter of the gear is d2 = 200 mm. Shaft material yield strength 335 MPa, tensile strength 600 MPa, Kç = 1.95, ka = 0.895, kb = 0.90 and safety coefficient = 1.4now that
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.40 in. and a wall thickness of 0.1375 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 58 in., L2 = 16 in., L3 = 16 in., and L4 = 28 in. The torques applied to the shafts have magnitudes of TB = 970 lb·ft, TD = 430 lb·ft, and TE = 170 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A.