Good Day, Kindly help me with this problem, Thank youP.S. T= 30 degrees A cast iron tank 25 mm thick contains a solution which is kept to boil at 95°C. Theouter surface of the tank is maintained at {T}°C, while the inside of the tank iscovered with a layer of enamel 1 mm thick (k = 0.86 W/mK). The heat transfercoefficient for the boiling solution is 4.5 kW/m²K. Calculate the overall heat transfercoefficient. Usek = 50 W/mk for cast iron. Write your answer to 2 decimal places.

Answered: Image /qna-images/answer/e0caa883-e2b6-4d66-acc1-700f95f085c0.jpg

Answered: A cast iron tank 25 mm thick contains a…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.3P

See similar textbooks

Similar questions

Water in a tank is to be boiled at 143.27 Pa absolute pressure by a 1.5-cm-diameter brass heating element equipped with electrical resistance wires inside, as shown in the figure. Determine the maximum heat flux that can be attained in the nucleate boiling regime and the surface temperature of the heater in that case. (3.23x105 W/m2, 118.6°C)
In boiling water at 1 atm pressure outside a stainless-steel tube with a surface temperature of 410F, the heat-transfer coefficient h in the absence of radiation is 32 Btu/h*ft^2*F. If the emissivity of the stainless steel is 0.8, will radiation significantly augment the rate of boiling (e.g., by more than 5 percent)? Assume that the vapor film is transparent to radiation and the boiling liquid is opaque.
(About measuring specific heat capacity) Since metal sample can be heated to any desired temperature value, say, 65°C or 156°C. Why is it practical to set the initial temperature of the metal sample near the boiling point of water? In connection to this, why should the dipper be partly submerged in the water while heating the metal sample?
There is a long rod, insulated to avoid any heat loss on its sides, is in perfect thermal contact with the boiling water (at atm pressure) at of the one end and with the ice-water mixture. The rod has a 1.00 m section of copper (with one end in boiling water) connected and joined together end-to-end to a length, L2, of steel (with one end in the ice water). Both sections of the rod have cross-sectional areas = 4.00 cm2. The temperature of the copper-steel junction is 65.0 °C after a steady state has been met. How much heat per second flows from the boiling water to the ice-water mixture? kCopper = 380 W/m*K kStainless Steel = 50 W/m*K A. How much heat per sec (watts) flows from boiling water to ice water mixture? B. Find the length L2 of steel section in meters
Determine the convection heat of a boiler if you are given the following data: Because boiling is taking place, use a value of 5,000 W/m2 * K as the convection heat transfer coefficient. T1 is the temperature of the boiler. water is 25°C and the T2 of steam is 110°C
Four cubic meters of water is to be heated by means of four 1.5 kW, 230-V immersion heating elements. Assuming the efficiency of the heater as 90%, determine the time required in boiling the water if the initial temperature is 20°C and if the elements are connected two in series in parallel with two in series. the answer is 275.6 hrs (According to the ECE board exam answer key) can you show me the solution?
Water is boiled at 250°F by a 2-ft-long and 0.5-in diameter nickel-plated electric heating element maintained at 280°F. Determine (a) the boiling heat transfer coefficient, (b) the electric power consumed by the heating element, and (c) the rate of evaporation of water.
Determine the cost of heating 6 gallons of water at room temperature of 19 ∘∘C to the boiling point at the energy rate of P14 per KW-HR. Assuming a heat loss of 21%.
A copper rod, an aluminum rod, and a brass, each 6.00 m length and 1.00 cm diameter, are placed end to end with the aluminum rod between the other two. The free end of the copper rod is maintained at water’s boiling point, and the free end of the brass rod is maintained at water’s freezing point. If T1 and T2 are steady-state temperature copper-aluminum junction and aluminum-brass junction respectively. Where TC is temp at freezing point of water and TH is temp at boiling point of water. Show that the steady-state temperature for (a) the aluminum-brass junction is:
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.51 m and is kept at 111 deg C. What is the power required to boil the water? Tsat = 100°C; Properties of water at 100°C: Density, ρl= 961 kg/m3; Kinematic viscosity, ν = 0.293x10-6 m2/s; Prandtl Number, Pr = 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, μ = ρ × ν = 961 × 0.293 × 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 kJ/kg; ρv = 0.597 kg/m3; σ = 0.0588 N/m; Csf=0.013; n=1; Select one: a. 25964.0356 b. 52997.1101 c. 49373.4011 d. 38911.7986
What is boiling and when does occurs? Explain pool boiling. How does it differ from forced convection boiling?
Explain the P-v-T surface of a substance that expands on freezing (like water).

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning