A centrifugal air compressor compresses air at 3, the rate of 0.7 m°/s from 85 kPa to 650 kPa. The initial specific volume is 0.35 m/kg and final specific volume is 0.1 m°/kg. If the suction line diameter is 10 cms and the discharge line diameter 6.25 cm. Determine : (i) the change in flow of work; (ii) the mass rate of flow; (iii) velocity change. 3

A centrifugal air compressor compresses air at 3, the rate of 0.7 m°/s from 85 kPa to 650 kPa. The initial specific volume is 0.35 m/kg and final specific volume is 0.1 m°/kg. If the suction line diameter is 10 cms and the discharge line diameter 6.25 cm. Determine : (i) the change in flow of work; (ii) the mass rate of flow; (iii) velocity change. 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A centrifugal compressor pumps 45.3 kg / m * i * n of air at 101.32kPa and .6 degrees * C to 345 kPa and 132 degrees * C by an irreversible process. Thetemperature rise of 22.1 kg / m * i * n of circulating water about the casing is6.7°C. What is the horsepower required? Neglect kinetic energy changesand no heat loss to surroundings.
A pump at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, determine electricity required to keep the process running for 24 hours.
A Francis turbine rotates at 1600 rpm and a flow rate of 1 m3/sec enters it. The inlet and outlet diameters are 1.2 m and 0.55 m, respectively, and the corresponding sections between the blades are 0.24 m2 and 0.08 m2. The outlet angle of the water from the distributor is 10º, the outlet angle of the wheel b2 = 40º and the manometric efficiency of the turbine is 78%.Determine:a) The net jumpb) The torque and power on the shaft
2. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079ft/cu. ft and discharges it with a density of 0.304 lb/cu. ft. At the suction, P 1 = 15 Psia; atdischarge, P 2 = 80 psia. The increase in the specific internal energy is 33.8 BTU/lb and the heattransferred from the air by cooling is 13Btu/lb. Determine the work on the air in BTU/min and inhp. Neglect kinetic energy. 3 decimal in final answer pls
A centrifugal fan supplies 4.7m3/s of air at a total static pressure of 325Pa. If the fan efficiency is %06 and rotates at a speed of 950rpm and supplies air with a velocity of 12m/s, determine the fan total pressure, air power, and fan power?
In a centrifugal blower (Figure Q1) air enters in to the blower normal to the blades (a1 = 0°), and exits at 40°from the radial direction (∞2=40°). The blower rotates at w = 200 rad/s. The inlet radius r1 = 4 cm, and inlet widthb1 = 6 cm. The outlet radius r2 = 10 cm and outlet width b2 = 3 cm. Assuming 100% etticiency and considering 0.2m3/s flow rate, calculatea) the net head produced by the blowerb) the breaking horsepower in watt.(Take density of air Pair = 1.2 kg/m', gravity, g = 9.81 m/52)
Solve the problem. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/cu ft and discharges it with a density of 0.304 lb/cu ft. At the suction, pressure is 15 psia, at discharge pressure is 80 psia. The increase in the specific internal energy is 33.8 Btu/lb and the heat transferred from the air by cooling is 13 Btu/lb. Determine the work on the air in Btu/min and in hp. Neglect change in kinetic energy.
A turbine is discharging 10m3/s under a head of 22 m at 200 rpm. The efficiency is 90%. Determine the performance of turbine under a head of 44 m.
A mini hydro power station takes in 3 cubic meters per second of water from a wide open reservoir through its turbine from an elevation of 15 meters and discharges to its surroundings at 0.50 m/s. During data gathering, the rotational force of the turbine shaft is measured 250 N for a distance of 2 m from its center axis at 2,850 rpm. If the electrical generator is 88% efficient, determine the turbine efficiency and the electrieity output of this station. Show the energy or schematie diagram and label it accordingly.
During the execution of a reversible non flow process the work Is -156.2 KJ. If V1 =0.845 cubic meter and the pressure varies as P= -730V+690 KPaa where V is in cubic meter, Determine the final volume
Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the pressure p2 = 5kPa. There is an orifice between the two chambers with diameter of 6 cm, Cc= 1.00, Cv=0.95 and the head of the liquid(s=2.50) over the orifice is 1.80 m. Find the actual flow rate through the orifice. Include the free body diagram if needed. a.45 L/s b.15 L/s c.35 L/s d.25 L/s
I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle inlet has an area of 90 cm^2, determine: a) The Volumetric flow rate at the in let (m^3/s) b) The Mass flow rate (kg/s) through the nozzle; c) The exit area of the nozzle (cm^2)