Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

Q: A certain engine has the following specifications for valve events: IVO at 12° before HDC, IVC at…

A: Brake Power is the power used to reduce the speed or torque of a machine. This can be generally…

Q: In an internal combustion engine, explain how the intake valve motion is achieved using the…

A: A cam is a mechanical device that is used to transmit the motion to a follower by direct contact. A…

Q: the mean output torque and flywheel inertia required for an engine

A: Given:   Cs=0.1 N=1500 rpm To determine: Mean torque Inertia of the flywheel

Q: Q / What is the number of crankshaft rotations during 3600 (R. P. M) in 1- Two-stroke engine 2- In…

A: Understand that the two stroke engines completes on complete cycle in one rotation 360 degrees of…

Q: The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston…

A: To find: The speed of the compressor. Given: The bore diameter of an air compressor is d=276 mm1…

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: three-cylinder in-line engine

A:

Q: 8. What will be the total piston displacement in a two-cylinder 100 mm x 130 mm engine?

A:

Q: Draw a schematic diagram of a supercharged engine and a turbocharged engine layout:

A: Given:- Supercharged turbocharged engine brief introduction To find:- Schematic of Supercharged…

Q: Drag text boxes to label diagram of a typical valve spring retaining mechanism

A: Valve is a mechanical device that is used to to provide the passage to the inlet or exhaust of a…

Q: Ignoring friction, how much force must the hydraulic cylinder exert to lift the engine? 6 ft 2 ft…

A: The force needs by the hydraulic  to lift the engine have to be calculated

Q: Give examples of calculation turning moment (torque) on the crankshaft piston

A: given data; Give examples of calculation turning moment (torque) on the crankshaft piston.

Q: By the analysis of figure 1 above, compare the speed of the extend and retract of the hydraulic…

A: From the analysis of the given figure

Q: Discuss the main advantages and disadvantages of at least 2 drive systems that can be used to drive…

A: The drive systems that can be used to drive camshaft are chain drive , gear drive and belt drive.

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: Explain basic concept of turbocharger or supercharger.

A: "Supercharger" is the generic term for an air compressor used to increase the pressure or…

Q: Explain the working of two stroke petrol engine with a diagram

A:

Q: - Low-speed shaft - Gearbox JI Rotor Hub- kel - High-speed shaft k2 Nacelle- Blade de

A: Solution

Q: Choose the Proper Answer for EACH of the followings: i) The under-square engine is the engine where:…

A: As the student posted multiple question, but as per the guidelines, I can solve only first question.…

Q: Torque =230 N-m

A: The torque for designing a rigid flange couple is given as,  T=250 N-mT=250×103 N-mm The number of…

Q: 1) Draw a simple sketch of your regulator design 2) Draw a simple sketch of the spring

A:

Q: With neat diagram, explain the wind turbine components such as Rotor, Drivetrain and Control System.

A: Block diagram for a wind turbine:

Q: kw per cylir of the crank and combu

A:

Q: r solve the problem related to ic engine s

A: Givenspeed n=15000brake load b=1500NIMEP =10barcalorific value cf=20kJ/ltrbrake circumference…

Q: 2- The need of turbocharging system is a) heat up combustion chamber c) speed up the intake air 3-…

A: (2) To choose: The correct option. Explanation: Turbocharger: A centrifugal compressor that increase…

Q: G) bore and stroke of compressor in mm (k) power of motor to drive the compressor

A:

Q: Doosan Man 6L60MC-C8 (2 stroke) Engine, piston stroke 2022 mm. Engine maximum power at 108 rpm is…

A: Write the given information.

Q: Question: What controls the instroke of a Single-Acting Cylinder? Note: -NO PLAGIARISM PLEASE. -200…

A: Valves controls the instroke of a Single-Acting Cylinder.

Q: The bolt size of cylinder head in a reciprocating compressor is a. M16

A: The bold size of the cylinder head in a reciprocating engine M16 option (a) is correct.

Q: What would happen if one of the Flow Controls were reversed in a cylinder?  What are the…

A: Consider the cylinder as an open system. To implement the flow controls, consider the control volume…

Q: 1. Introduction of the project 2. Sources of Vibration - Determine and discuss the sources of…

A: We are to determine the sources of vibration in this assembly

Q: neat diagram, explain the wind turbine components such as Rotor, Drivetrain and Control System

A: The kinetic energy of wind waves when converted into electrical energy this mechanical process is…

Q: 2- Draw theoretical valve timing diagram and compare it with actual one.

A:

Q: In most of internal combustion engines, crankshaft bearing is  Select the correct answer below: A.…

A: Concept: Hydrodynamic bearing: 1) In this bearing, two rubbing surfaces of bearing are separated by…

Q: introduction about Control of Single and Double Acting Cylinder

A: A single-acting cylinder in a reciprocating engine is one in which the working fluid only…

Q: The cam and the follower have a ------ which constitute as a higher pair.

A: Cam and follower is a mechanism which is used to convert rotation to linear ( a reciprocation )…

Q: What kind of crankshaft should you use for a v-type engine with 12-cylinder assembly?

A: Common crank shaft is used in a v-type engine.

Q: Q5. Explain the actual Indicator and valve timing diagrams for a Four Stroke Cycle Diesel Engine.

A:

Q: Draw the p-V diagram and typical valve timing diagram for a two stroke IC engine.

A: The P-V Diagram for the two stroke engine is Here process 1-3 is the compression process and…

Q: enlist the engine operations at the time of both hard acceleration and deceleration and idle.

A: To describe the operation when the engine is accelerating and decelerating.

Q: Explanation why it is necessary to determine the mass of moving parts before analyzing and…

A: Given:The single slider crank mechanism consists of piston, cylinder,connecting rod and crank shaft.

Q: Describe a 4-stroke compression ignition engine operation with neat sketches.

A:

Q: What are the types of cam mechanism explain the solution with the problem

A: Cam Mechanism: Cam and followers are used simultaneously and combinedly they are termed as cam and…

Q: rpm diesel engine and operating under moderate shock load. The pump will operate at 800 rpm. The…

A:

Q: Which one of the following is not regulating the mean speed of an engine, when there are variations…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.