A CI is desired for the true average (i.e. population mean) stray-load loss u in watts for a certain type of induction motor when the line current is held at 10 amps for a speed of 1500 rpm. Assume that stray-load loss is normally distributed with o = 3.0 a. Compute a 95% CI for µ when n= 25 and x = 58.3 b. Compute a 95% CI for µ when n = 100 and x = 58.3 c. Compute a 99% CI for µ when n= 100 and x = 58.3 d. How large must n be if the width of the 99% interval for u is to be 1.0?

A CI is desired for the true average (i.e. population mean) stray-load loss u in watts for a certain type of induction motor when the line current is held at 10 amps for a speed of 1500 rpm. Assume that stray-load loss is normally distributed with o = 3.0 a. Compute a 95% CI for µ when n= 25 and x = 58.3 b. Compute a 95% CI for µ when n = 100 and x = 58.3 c. Compute a 99% CI for µ when n= 100 and x = 58.3 d. How large must n be if the width of the 99% interval for u is to be 1.0?

MATLAB: An Introduction with Applications

6th Edition

ISBN:9781119256830

Author:Amos Gilat

Publisher:Amos Gilat

Chapter1: Starting With Matlab

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the following 10 measurements about the cohesion of a soil: 12 kPa, 14 kPa, 15 kPa, 14.5 kPa, 16.0 kPa, 18 kPa, 15 kPa, 16.2 kPa, 17. 6 kPa, 13 kPa. Work out the solutions of the following two problems, assuming the cohesion follows the normal and lognormal distributions, respectively. (1) Draw the PDF of the cohesion; (2) Evaluate the probability that the cohesion based on the PDF is less than 5 kPa, 10 kPa, and 15 kPa; (3) Assess the effect of the type of distribution on the results.
A CI is desired for the true average stray-load loss ? (watts) for a certain type of induction motor when the line current is held at 10 amps for a speed of 1500 rpm. Assume that stray-load loss is normally distributed with ? = 2.2. (Round your answers to two decimal places.) (a) Compute a 95% CI for ? when n = 25 and x = 53.7. , watts(b) Compute a 95% CI for ? when n = 100 and x = 53.7. , watts(c) Compute a 99% CI for ? when n = 100 and x = 53.7. , watts(d) Compute an 82% CI for ? when n = 100 and x = 53.7. , watts(e) How large must n be if the width of the 99% interval for ? is to be 1.0? (Round your answer up to the nearest whole number.)n = You may need to use the appropriate table in the Appendix of Tables to answer this question.
A small electronic device is designed to emit a timing signal of 200.0 milliseconds (ms) duration. This device is specified as 201.0 + 10.0. In the production of this device, subgroups of six units are taken at periodic intervals and tested. Xbar and R are calculated for each subgroup and used to plot control charts. The results of inspection of 25 subgroups, ΣX = 5,000.00 and ΣR = 277.00. Assuming that the mean of the process shifts to 196 V dc, compute the Type II Error probability that it will not be detected on the first subgroup drawn after the shift occurs.
1. Consider the Gaussian distribution N (m, σ2).(a) Show that the pdf integrates to 1.(b) Show that the mean is m and the variance is σ.
Suppose that n observations are chosen at random from a continuous pdf fY(y). What is the probability that the last observation recorded will be the smallest number in the sample? I asked this question earlier today, but didn't quite understand all of the response. P(y1<=yn)p(y2<=yn) and so on was used, but shouldn't the yn be listed first in the inequality since we want to know if yn is the smallest?
The diameter of a metal shaft used in a disk-drive unit is normally distributed with mean 0.2508 in. and std. dev. 0.0005 in. The specification on the shaft have been established as (0.25-0.0015 in, 0.25+0.0015in) If the process mean has been adjusted to 0.25 in, what fraction of the shafts produced does NOT conform to specifications? a). 0.0027 b). 0.0013 c).0.08 d). 0.16
Suppose that X is a continuous unknown all of whose values are between -3 and 3 and whose PDF, denoted f , is given by f ( x ) = c ( 9 − x^2 ) , − 3 ≤ x ≤ 3 , and where c is a positive normalizing constant. What is the variance of X?
Derive a general expression for the variance of net future loss Var(L) with a constant force of interest δ under each of the following models:i. μ_x(t) = μii. μ_x(t) = 1/(ω-x)
a. What is the probability that the lifetime X of the first component exceeds 3? b. What are the marginal pdf's of X and Y? Are the two lifetimes independent? x. What is the probability that the lifetime of at least one component exceeds 3?
Suppose X1, ..., Xn have been randomly sampled from a normal distribution with mean 0 and unknown variance sigma^2, and let U = c * i=1 -> n summation (X_ i)^2 , where c is a constant. Find the value of c that minimises the Mean Squared Error (MSE)
A theoretical justification based on a certain material failure mechanism underlies the assumption that ductile strength X of a material has a lognormal distribution. Suppose the parameters are μ = 4.8 and σ = 0.11. 1. Compute E(X) and V(X). (Round your answers to three decimal places.) 2. Compute P(X > 125). (Round your answer to four decimal places.) 3. Compute P(110 ≤ X ≤ 125). (Round your answer to four decimal places.)
Suppose the proportion X of surface area in a randomly selected quadrat that is covered by a certain plant has a standard beta distribution with ? = 4 and ? = 2. (a) Compute E(X) and V(X). (Round your answers to four decimal places.) E(X) = V(X) = (b) Compute P(X ≤ 0.3). (Round your answer to four decimal places.)(c) Compute P(0.3 ≤ X ≤ 0.7). (Round your answer to four decimal places.)