A circuit comprises of an impedance Z, = (2 + j0) 2 n series with the parallel combination of two impedance Z, (10 +j15) Q and Z3 = (6- j8) n. Which of the following is the average power dissipated in the third impedance (Z) if the total current supplied to the circuit is 15A? %3D Oa. 541.5W O b. 3750W Oc. 737.88W O d. 1439.641T

A circuit comprises of an impedance Z, = (2 + j0) 2 n series with the parallel combination of two impedance Z, (10 +j15) Q and Z3 = (6- j8) n. Which of the following is the average power dissipated in the third impedance (Z) if the total current supplied to the circuit is 15A? %3D Oa. 541.5W O b. 3750W Oc. 737.88W O d. 1439.641T

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Similar questions

The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, the amplitude of the current that will pass through the circuit, the phase angle and the angular frequency of the circuit are given in which option correctly. AB=61 AB=16 Answers I need: current= ?? angular frequency = ?? phase angle = ??
The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to ZL.1. a) Find the maximum average power delivered to ZL.2. b) What percentage of the total power developed in the circuit isdelivered to ZL?
1. a) Determine the load impedance for the circuit shown that will result in maximum average power being transferred to the load if ω=10 krad/s.2. b) Determine the maximum average power delivered to the loadfrom part (a) if vg=120cos10,000t V.3. c) Repeat part (b) when ZL. consists of two components fromAppendix H whose values yield a maximum average power closestto the value calculated in part (a).
The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
Problem : The industrial load requires 40 kW with a power factor of 0.84 leading. The load voltage is 220 Vrms at 60 Hz, and the transmission line impedance is 0.1 + j0.25Ω. Calculate the active and reactive power losses on the transmission line and determine the required active and reactive power at the input end of the transmission line. The answer given : Pline=4.685 kW, Qline=11.713 kvar, PS=44.685 kW, QS=37.55 kvar and I want to know the concept of 'Complex Power'.
The load impedance ZL in the circuit is adjusted until maximum average power is transferred to ZL.1. a) Specify the value of ZL if N1=3600 turns and N2=600 turns.2. b) Specify the values of IL and VL when ZL is absorbingmaximum average power.
4 Sinusoidal voltage source of us(t) = [100 cos ωt]V , (ω = 20Mrad s ) voltage is connected to the input of a transmission line of h = 10m length. The wawe parameters of the line and the impedance of the loading two-pole connected to the output at ω angular frequency are: Z0 = (49, 5 - j2)Ω, γ = (0, 5 + j40)km-1, and Z2 = Z0. Find the voltage amplitude at the nearest point to the source where the voltage phase angle is 0! a) U = 100V b) U = 92, 4V c) U = 36, 8V d) U = 50V