A circular shaft AB consists of a 250 mm long, 22 mm diameter steel cylinder which is 125 mm long and a 16mm diameter cavity has been drilled from the other end B. The shaft is attached to fixed supports at both ends and a 120 N-m torque is applied at its mid- section. a) Determine the torque exerted on the shaft at A. b) Determine the torque exerted on the shaft at B.

A circular shaft AB consists of a 250 mm long, 22 mm diameter steel cylinder which is 125 mm long and a 16mm diameter cavity has been drilled from the other end B. The shaft is attached to fixed supports at both ends and a 120 N-m torque is applied at its mid- section. a) Determine the torque exerted on the shaft at A. b) Determine the torque exerted on the shaft at B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel shaft BCD (G=80 GPa) of total length 3 m is encased for 1/3 of its length by a bronze sleeve ABC (G=41 GPa) that is securely bonded to the steel. The diameter of the steel is 60 mm while the outer diameter of the bronze is 80 mm. a. What is the maximum allowable torque in gear A if the allowable shear stresses in the steel and bronze are limited to 110 MPa and 70 MPa, respectively; and the angle of twist between A and D is limited to 9o? b. What power is supplied by the motor that corresponds to the computed torque at A if shaft EF rotates at 200 rpm? The diameter of gear E is 60 mm while gear D has a diameter of 100 mm.
A steel shaft of diameter 60 mm and length 3.5 m is fixed at its ends A and B. If two torques of the same direction are applied, a 500 Nm torque at C (Im from the left end) and a 200 Nm torque at D (1m from the right end), determine the maximum internal torque in the shaft.
A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a 5-in.-long, 58-in.-diameter cavity has been drilled from end B. The shaft is attached to fixed supports at both ends, and a 90 lb?ft torque is applied at its midsection . Determine the torque exerted on the shaft by each of the supports.
A compound steel [G = 80 GPa] shaft consists of a solid 92-mm-diameter segment (1) and a solid 60-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC ≤ 4°. Determine the magnitude of the largest torque TC that may be applied at C.
A hollow shaft's inner diameter is half of its outer diameter D. Show that the maximum torque that this shaft can carry is 15/16th of the maximum torque that a solid shaft of diameter D made of the same material can carry.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
A 2.25-kN·m torque T is applied to the solid cylinder made up of a hollow cylinder and an inner core as shown.Determine the percent of the torque carried by the inner 25-mm-diameter core.
An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa, Determine the relative angle of twist of gear D relative to gear A (in degrees). What is the direction of the rotation of A relative to D?
A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length having an external diameter of 16mm and a wall thickness of 3mm. The rod and tube are rigidly connected at their ends so that they twist together when a torque of 20 Nm is applied. Galuminum = 30GPa; Gbrass = 40GPa. Determine: a) The values of the torsional stiffness for the rod and the tube b) The torque transmitted by each c) The maximum shear stress in each d) The angle of twist
The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange B, determine the torque in pipe (1).
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.