A closed cylindrical tank having a radius of 0.60m and a height of 4m is full of water under a pressure of 196.2 kPa. If the vessel is rotated at 200 rpm: (a) Compute the total pressure on the side wall and (b) compute the total pressure against the top. Imaginary water surface y%3D8.04 Closed- h=20 4m C P=wh -1.2-

A closed cylindrical tank having a radius of 0.60m and a height of 4m is full of water under a pressure of 196.2 kPa. If the vessel is rotated at 200 rpm: (a) Compute the total pressure on the side wall and (b) compute the total pressure against the top. Imaginary water surface y%3D8.04 Closed- h=20 4m C P=wh -1.2-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the pressure (in kN/m2) in the pipe shown (Pressure A) if y=1.24 m, h=1.02 m, and the manometry fluid is mercury (Specific Gravity=13.6).
An open tank contains 4.93m of oil (sp.g=0.8) and 5.51? of water. Find the pressure (Kpa) at the midpoint level of water
A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm dimeter for the remaining 10 m is connected to a water tank. The height of waler in tank is 15 m above the centre line of the pipe. Find out the flow rate through the pipe, taking all losses into the account. Consider the reduction in diameter of the pipe as sudden coefficient of friction for the pipe is 0.008.
A closed cylindrical vessel is filled with water 3/4 of its height. The height is 4 meters and the diameter is 2 meters. The remaining 1/4 is filled with air, the pressure which is 100 kPa. If the closed cylindrical vessel is rotated at 152 revolutions per minute, determine the maximum and minimum inside pressure at the base. (Ans. minimum= 100 kPa, maximum 215 kPa)
A 300 mm cast-iron pipe is discharge 120 lit/sec. At a point 200 m from the reservoir the center of the pipe is 30 m below the reservoir surface. What is the pressure in kPa to be exerted there? Assume f= 0.02
Oil with sp. gr. 0.95 flows at 200 lit/sec through a 500 m of 200 mm diameter pipe (? = 0.0225). Determine (a) the head loss (m) and (b) the pressure drop (kPa) if the pipe slopes down at 10⁰ in the direction of flow.
Water flows at the rate of 0.015 m3/s through a 100 mm diameter orifice used in a 200 mm pipe. What is the difference of pressure head between the upstream section and the vena contracta section? Take co-efficient of contraction Cc = 0.60 and Cv = 1.0.
A cylindrical pipe with water flowing downward at 0.02 m/sec having top diameter of 0.08 m, bottom diameter of 0.04 m and a height of 1.5 m. Find the pressure between the pipe.
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
A rectangular tank 6m long, 2m wide and 2m deep contains water to a depth of 1m. Itis accelerated horizontally at 2.5 m/s2 in the direction of its length. Determinea) Slope of the free surfaceb) Maximum and minimum pressure intensities at bottom
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.