A pipe 300m long has a slope of 1:100 and converts from a 1-m diameter at itsupper end, where the pressure is 6.87x10ʻkg/m-sec? (68.7kN/m?). To 0.5m at itslower end. If the water flows at a rate of 5400lit/min, determine the pressure atthe lower end. Assume the energy loss due to friction is negligible.A11A22.300m

Continuity Equation Continuity equation is established on the principle of conservation of mass, it…

A pipe 300m long has a slope of 1:100 and converts from a 1-m diameter at its upper end, where the pressure is 6.87x10ʻkg/m-sec? (68.7kN/m²). To 0.5m at its lower end. If the water flows at a rate of 5400lit/min, determine the pressure at the lower end. Assume the energy loss due to friction is negligible.

A pipe 300m long has a slope of 1:100 and converts from a 1-m diameter at its upper end, where the pressure is 6.87x10ʻkg/m-sec? (68.7kN/m²). To 0.5m at its lower end. If the water flows at a rate of 5400lit/min, determine the pressure at the lower end. Assume the energy loss due to friction is negligible.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows down a vertical pipe whose diameter increases suddenly from 175 mm to 350 mm. The discharge in the pipe is 85 lps. The pressure 0.6m above the enlargement section is 275 kPa. Find the pressure at a section 0.6 m below the enlargement section.
Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at a rate of 0.0556m^3/s. Ans: 21.7 m
A pipeline connected to a reservoir discharges water 30 m below the free surface in the tank. The pipeline crosses a ridge whose summit is 9 m above the level of free surface and 300 mm distant from the reservoir. The pipe is 0.6 m in diameter and 3 000 m long and the connection is sharp and sudden. Take ƒ = 0.0075. Finda, the minimum depth below the ridge at which the pipe must be laid, if the absolute pressure in the pipe is not to fall below 3 m of water.b, the discharge
Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s.
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
6. Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s. indicate free body diagram
Calculate the diameter of vertical pipe needed for flow of liquid at R = 1800 when the pressure remains constant. v = 1.5 um?/s.
A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The friction loss is 10 ft for flow in either direction when the velocity at the top is 30 fps and the pressure head there is 6.5 ft of water. Find the pressure head in ft at the bottom when the flow is upward. a.69.6 b.58.0 c.89.6 d.46.0
Compute the lost pressure for a converging fitting. The flow rate in the 20 cm upstream section is 0.24 m3/s, and the flow rate in the 20 cm branch is 0.24 m3/s. The downstream section has a diameter of 25 cm. Assume a 45-degree wye. Figure Wye 4
A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The friction loss is 10 ft for flow in either direction when the velocity at the top is 30 fps and the pressure head there is 6.5 ft of water. Find the pressure head in ft at the bottom when the flow is downward.
A pipe AB carries water and tapers uniformly from a diameter of 0.1 m at A to 0.2 m at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). (Please round-off final answer to four decimal places) Determine the pressure in bars, recorded at C neglecting all losses. (Please round-off final answer to 2 decimal places)