A column ABC is constructed with uniform hollow circular section as shown below. The roof load at the top of column is 50 kN and the floor load at mid height is 150 kN. The compressive stresses in the portion AB and BC are and respectively. 50 kN 200 mm 150 kN 15 mm X-X

A column ABC is constructed with uniform hollow circular section as shown below. The roof load at the top of column is 50 kN and the floor load at mid height is 150 kN. The compressive stresses in the portion AB and BC are and respectively. 50 kN 200 mm 150 kN 15 mm X-X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam with length of 3.2 m is reinforced with As=5720 mm^2 tension reinforcement and compression reinforcement A's =1905 mm^2 placed at 60 mm from extreme compression fiber. The effective depth is 550 mm and width of 400 mm. Use f'c=35 MPa and fy=415 MPa. 1. Calculate the magnitude of the neutral axis. 2. Determine the compressive force of the section. 3. Determine the safe concentrated live load that can be placed at the free end if the beam carries a total ultimate uniform load of 35 kN/m.
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. b) What is the value of fs' (actual stress of the compression bars)
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. determine 1.) a 2.) the value of fs' (actual stress of the compression bars) 3.) value of ρbalance 4.) Mu
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
A square tied column 400 mm on each side is reinforced with 8 – 25 mm bars with fy = 275 MPa.Assuming fc’ = 22 MPa, determine the ultimate axial load capacity of this column.a. 2250 kN c. 2243 kNb. 2239 kN d. 2356 kN
A steel tank 2m by 1.5m by 1.2m weighs 10KN when empty and is supported by two steel beams spanning 2.0m and each weighing 10KN. Design a suitable square section for the steel beams if the tank is filled water weighing 10KN/m^3 using the plastic method. The permissible bending stress on the section is 140N/mm^2 and factor of safety is 1.5
A 5.0m long simply supported reinforced concrete beam has awidth of 350mm and an overall depth of 470mm. The beam is reinforced with 2 –28mm dia. compression bars on top and 4 –28mm dia. tension bars at the bottom, each located 70mm from the extreme concrete fiber. Concrete strength f’c = 21MPa and steel yield strength fy = 345MPa. Determine the following, A.Depth of compression block assuming both tension and compression steel yields. B.What is the ultimate moment capacity of the beam in kN.m? C.Determine the additional concentrated live load that can be applied at midspan if the deadload including the weight of the beam is 15kN/m. Hello please answer this thanks
A prismatic beam having 250 mm x 500 m is reinforced for flexure at the bottom with 4-416 mm with an effective depth of 420 m. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kn/m3, Concrete strength f'c= 24 MPa and rebar strength fy=280 MPa. 1. Determine the resulting depth of the uniform rectangular stress block in a when the bean section reaches tlimate stage. (A to D) 2. Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. ( E to H) 3. Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight. (I to L) A 44.15 B. 78 85 c. 57.34 D, 98.56 E. 195.66 F. 89.60 G.133.91 H. 110.15 I 16.31 J. 39.16 K. 26.16 L. 20.51
Solve the problems using the prescribed problem formulation and appropriate approach. 2. The beam shown carries a concentrated load P = 12 kN and a uniformly distributed load wO = 225 N/m. The dimensions a, b, and c are 1.0 m, 1.2 m and 1.4 m, respectively. If the beam is a 50 mm x 100 mm x 3 mm hollow tube (b x h x t), determine the maximum bending stress, the maximum vertical shear stress, and the deflection under the load P.
Determine the Pn of the following column assuming it had no moment on it and only an axial compression force: (f’c = 6000 psi, Grade 60 bars, h = 20”, b = 12” (i.e. rectangular section), tied column). Do not worry about calculating φ (phi factor). You can assume it is a short column. Also assume a reinforcement ration of 2% (ρg = 0.02).
A steel column (E = 200 GPa) is 9 m long, embedded in aone end and supported on the other. If the section is shown below, determine the buckling tension.