A compression member of 6.5-m effective length is made by welding together two L152 x 102 × 12.7 angles as shown. Using E= 200 GPa, determine the allowable centric load for the member if a factor of safety of 2.2 is required. 152 mm 102 mm 102 mm The allowable centric load for the member is 195 KN.

A compression member of 6.5-m effective length is made by welding together two L152 x 102 × 12.7 angles as shown. Using E= 200 GPa, determine the allowable centric load for the member if a factor of safety of 2.2 is required. 152 mm 102 mm 102 mm The allowable centric load for the member is 195 KN.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
Two brass rods used as compression members, each of 3-m effective length, have the cross sections shown. (a) Determine the wall thick-ness of the hollow square rod for which the rods have the same cross-sectional area. (b) Using E= 105 GPa, determine the critical load of each rod.
A column of 22-ft effective length is to be made by welding two 9 *0.5-in. plates to a W8 * 35 rolled steel shape as shown. Determine the allowable centric load if a factor of safety 2.3 is required. Use E=29 *106 psi
The horizontal link BC is 6.35 mm thick, has a width w = 31.8 mm, and is made of steel with ultimate tensile strength equal to 483 MPa. What should be the factor of safety to be used if the structure shown is designed to support a load P = 44.5 kN.
Member AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins at A and B pass through the centroid of the cross section of the channel, determine the factor of safety for the load shown with respect to buckling in the plane of the figure when θ= 30°. Use Euler’s formula with E= 200 GPa.
Determine if the following column is long or short, and then determine the critical load on a steel column having a rectangular cross-section, 12mm by 18mm and length of 250 mm. it is fixed on both ends and made from a steel that has the following properties: E=209 Gpa and Sy=290 Mpa.
Determine the maximum allowable load P that can be applied to member BC without causing member AB to buckle. Assume that AB is made of steel and is pinned at its ends for x–x axis buckling and fixed at its ends for y–y axisbuckling. Use a factor of safety with respect to buckling of F.S. = 3. Est = 200 GPa, sY = 360 MPa.
A column of 3-m effective length is to be made by welding together two C130 *13 rolled-steel channels. Using E= 200 GPa, determine for each arrangement shown the allowable centric load if a factor of safety of 2.4 is required.
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
The load is supported by the four stainless steels wires that are connected to the rigid members AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 16mm2. Given that E= 200Gpa for all the steel wires. a) Draw Freee Body Diagram(FBD) of each rigid member. b) Determine the angle of tilt of each member after the 2250N load is applied
PLS ANSWER ASAP TY! For the assembly shown, a yoke on a 30 mm diameter rod is attached to a 25 mm thick bracket via 15 mm diameter bolt as shown. The ultimate axial strength in the 30 mm dia. rod is 150 MPa. a)Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5 with respect to the ultimate axial strength is required. b) What is the tensile axial stress on the rod (in MPa)? c) What is the shear stress on the bolt (in MPa)? d) What is the factor of safety for the 15 mm. dia. bolt with respect to the ultimate shear strength? (in 2 decimal places)