A compression spring is to be made from ASTM A227 steel wire, with a wire diameter of 8.0 mm, and is to operate under light service conditions. The spring is to have an inside diameter of 34 mm, with plain ends ground. If the number of active coils for this spring is 10 and it has a free length of 264 mm then its pitch must be:

A compression spring is to be made from ASTM A227 steel wire, with a wire diameter of 8.0 mm, and is to operate under light service conditions. The spring is to have an inside diameter of 34 mm, with plain ends ground. If the number of active coils for this spring is 10 and it has a free length of 264 mm then its pitch must be:

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
Determine the wahl's factor of a spring designed to fire a 3kg projectile. The outside diameter of the cil is 170 mm with 10mm wire diameter and a total of 20 coils squared and ground. The spring has a free length of 625 mm. When set or loaded the spring is compressed to a length of 444mm.
(2) A coil spring is to be used for the front suspension of a car. The spring is to have a rate of 400lb/in, an inside diameter of 4.0-in, & a free length of 14⅛-in, with squared & ground ends. The material is to be oil-tempered chrome-vanadium steel. Recommend the rod diameter & the number of coils for a design load of 1,500lb.
A helical compression spring having 14 active coils is close coiled. It has a spring stiffness of 400lb/in. It is cut into two springs having 6 and 8 turns. Determine the spring stiffnesses of resulting springs.
An engine valve spring must exert a force of 300 N when the valve is closed and 500 N when the valve is open as shown in Figure 3. The maximum lift of spring is 8 mm (ymax). With a safety factor of 1.6 a. Design the wire diameter. b. Calculate the number of active coils. c. Calculate the number of total coils and the free length. d. Check the stability. Design Decisions: The spring is made of ASTM, A227, unpeened, clash allowance of 0.15, G = 79 GPa, squared and ground ends and C = 6.
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.
Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.
A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.