Give the suitable specifications (width, thickness and length) for an open Flat-belt system to transmit a power of (74) hp at (620) rpm to a shaft with 280 rpm. Take a safety factor of (2). The smaller pulley is 250 mm diameter and the center distance is 5 m. the belt material is leather chrome tanned and the pulleys are of cast iron working in wet condition. The belts allowable tensile stress is 4.2 MPa

Give the suitable specifications (width, thickness and length) for an open Flat-belt system to transmit a power of (74) hp at (620) rpm to a shaft with 280 rpm. Take a safety factor of (2). The smaller pulley is 250 mm diameter and the center distance is 5 m. the belt material is leather chrome tanned and the pulleys are of cast iron working in wet condition. The belts allowable tensile stress is 4.2 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a multiple v-belt drive which is powered by a compressor-stator motor with speed 1300 rpm. The center distance must be between 30 to 40 inches and the available driver sheave diameter iS 14 inches. Recommend a multiple v-belt drive that respects the following condition stated.
A conveyor is driven by a 2.5-hp high-starting-torque electric motor through a flexible coupling to a worm-gear speed reducer, whose speed ratio is 35, and then via a roller chain to the conveyor shaft that is to turn about 12 rpm; motor rpm is 1750. Operation is smooth, 8 hr./day and service factor can be taken as 1.2. Decide the chain pitch in inch.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
The shaft of a belt drive is made of AISI C1020 as rolled steel. The belt tensions vary continuously during transmission at a constant tension ratio of 3:1; the maximum tight side tension being 400 lb and the minimum tight side tension is expected to be 160 lb, at a pulley diameter of 12 inches. For a Goodman factor of safety of 1.8, recommend the diameter of the shaft. Consider a machined surface and the effect of a hardened profile keyway in the shaft.
A band clutch has an angle of contact of 260 degrees on a 16 in diameter drum The rotational speed of the drum is 260 rpm and the clutch transmit 10 hp. The band is 1/16 - in. thick and has a designstress of 4800 psi. How wide should the band be?
4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, plain chain drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
An industrial fan running at 600 rpm is driven by a 25kW, 960rpm, induction motor using an open belt drive. The pulley is mounted on the motor shaft of 270mm diameter. Center distance between the two shafts is 1.45 meters and coefficient of friction is 0.35. Assume thickness of belt equal to 6.5 mm and an allowable stress of 2.86MPa for belt material. Calculate the following: a) Angle of lap for both pulleys; b) Length of the belt; and c) Width of the belt (disregard standard size).
Using safety factor of (3) , determine a minimum diameter for the shaft shown in FIGURE 2. The shaft material AISI 1050 HR ( hot rolled ) steel . The power to be transmitted is (8 KW) at ( 900 rpm). The diameter of the pulley is (250 mm ) and the ratio of belt tensions is (2.5 ). (90 percent ) reliability is desired.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.