A compressor draws in 0.1 m/s of air at atmospheric conditions of 1.013 bar and 22°C and delivers it to a large receiver in which the air stabilises at a temperature and pressure 28°C and 310 kPa gauge. The air then discharges back to atmosphere through a converging diverging nozzle located in the side of the tank. Ignoring losses in the nozzle. Determine the:

A compressor draws in 0.1 m/s of air at atmospheric conditions of 1.013 bar and 22°C and delivers it to a large receiver in which the air stabilises at a temperature and pressure 28°C and 310 kPa gauge. The air then discharges back to atmosphere through a converging diverging nozzle located in the side of the tank. Ignoring losses in the nozzle. Determine the:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The dry and saturated steam at a pressure of 10.5 bar is expanded isentropically in a nozzle to apressure of 0.7 bar. Determine the final velocity of the steam issuing from the nozzle, when (a) friction is neglected, and (b) 10% of the heat drop is lost. The initial velocity maybe neglected
In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low velocity. If the nozzle outlets are exposed to atmospheric pressure of 100 kPa. Using Bernoulli equation, determine the maximum velocity to which watercan be accelerated by the nozzles before striking the turbinebuckets.
Air flows steadily through a converging-diverging nozzle a mass flow rate of 3.00kg/s. The air enters the duct at a pressure of 1400kPa and a temperature of 200°C with a low velocity, and it expands in the nozzle to an exit pressure of 92kPa. The duct is designed so that the flow can be approximated as isentropic. Nozzle throat area must be ______ to sustain the flow.
Air flows steadily at low speed through a horizontal nozzle (by definition a device for accelerating a flow), discharging to atmosphere. The area at the nozzle inlet is 0.1 m2. At the nozzle exit, the area is 0.02 m2. Determine the gage pressure required at the nozzle inlet to produce an outlet speed of 50 m/s
Gas turbine operates with air. At the initial state the air has pressure of 1.3 MPa and temperature 773K, after the expansion, the air has pressure of 100 kPa and is at temperature 120C. The cross-sectional area of a turbine changes from 0.2 m2 to 1m2 respectively. Knowing that the initial velocity of air is 40 m/s, determine: a. mass flow rate. Use tables as needed. b. power generated by the turbine. Use tables as needed.
The compressor of a jet engine tested at sea level on a stationary test bed on a day when the atmospheric temperature and pressure is 298 K and 101kPa, respectively. When running at its design operating point, the masss flow rate through the compressor is measured as 15 kg/s and the rational speed is 6200 rpm. Determine the mass flow rate and the rational speed when the compressor is operating at the design operating point during high altitude cruise with an onlet stagnation temperature of 236 K and an inlet stagnation pressure of 10.2 kpa. The design pressure ratio of compressor is 20. If the compressor isentropic efficiency is determined from the test to be 85=, calculate the power input at the cruise condition. Assume for air that y=1. 4 and Cp=1005 kJ/kg-K throughout.
An adiabatic expansion of air occurs through a nozzle from 830 KPa and 750C to 140 KPa.The initial kinetic energy is negligible. For an isentropic expansion,4.1 Determine the specific volume4.2 Determine the final temperature4.3 Solve for the speed at the exit section
The dry and saturated steam at a pressure of 10.5 bar is expanded isentropically in a nozzle to apressure of 0.7 bar. Determine the final velocity of the steam issuing from the nozzle, when (a) friction is neglected, and (h) 10% of the heat drop is lost
Using Bernoulli's principle, determine the pressure change between the upstream and downstream end of the nozzle. The velocities at the entrance and exit are 2.55m/s and 1.13m/s,respectively. Note: Temperature is 20 degrees centigrade. Nozzle is horizontal.
In a turbo-jet engine the momentum of the gases leaving the nozzle produces the propulsive force. The enthalpy and velocity of the gases at the nozzle entrance are 1200 KJ/Kg and 200 m/s respectively. The enthalpy of the gas at exit is 900 KJ/Kg. If the diameter of the nozzle at exit is 500 mm and the gas density at the nozzle inlet and exit are 0.81 kg/m3 and 0.39 kg/m3 respectively. Determine the diameter of the nozzle at inlet. Pls show your solution in simple formula like fundamentals only and show all conversion of units
In a turbo-jet engine the momentum of the gases leaving the nozzle produces the propulsive force. The enthalpy and velocity of the gases at the nozzle entrance are 1200 KJ/Kg and 200 m/s respectively. The enthalpy of the gas at exit is 900 KJ/Kg. If the diameter of the nozzle at exit is 500 mm and the gas density at the nozzle inlet and exit are 0.81 kg/m3 and 0.39 kg/m3 respectively. Determine the diameter of the nozzle at inlet. Show conversion of units
Water enters a centrifugal pump axially at atmos-pheric pressure at a rate of 0.12 m3/s and at a velocity of7 m/s, and leaves in the normal direction along the pump cas-ing, as shown. Determine the force acting onthe shaft (which is also the force acting on the bearing of theshaft) in the axial direction.