A constructed beam ACB has a cross section of 1.5in X 1.5 in supported by a column CE having a cross section of 1in X 1in. Assuming that the allowable stresses for the connecting bolt for point C is 24 ksi for shearing and 30 ksi for bearing, determine the minimum diameter of the bolt required in Inches.

A constructed beam ACB has a cross section of 1.5in X 1.5 in supported by a column CE having a cross section of 1in X 1in. Assuming that the allowable stresses for the connecting bolt for point C is 24 ksi for shearing and 30 ksi for bearing, determine the minimum diameter of the bolt required in Inches.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.5P

See similar textbooks

Similar questions

Determine: a. max allowable Pu if the shearing if 0.5in bolts dia. governs b. max allowable Pu if the bearing of the tension member governs c. max allowable Pu if all "actions" are considered d. number of anchor bolts needed if an A992 steel bolt is used instead of A325. Assume force is equally shared by the bolts, and the anchor bolts are properly bonded on the ceiling
check the adequacy of W10 x 60 section to resist a service tensile load that induce the following forces: PD = 180k, E = 147.1 k and PL = 205k. The member length is 30ft and assumed to have two lines of holes in the web with 3" gauge. Assume there are four bolts in each line at 3 in c/c. All holes for 7/8 - in diameter bolts. The section must satisfy the slenderness effect.
2 hEe c W@ B & - For the beam shown find the value of Force (F) Ib and maximum stress due to flexure ( oy ) psi if the shear force in bolts is 300Ib and the shear stress in beam 120psi. Spacing between bolts (S) =5in F T —————————————+% 4ft 8ft 1in 1in -~ - 10in 1n § 8in
A built-up beam made from fastening two channels to a wide flange section carriesloads` as shown. The fasteners are 12mm∅ bolts with allowable shear stress τ= 110 MPa. Forbearing, σb= 220MPa for single shear, and σb= 275 MPa for double shear. E=200 GPA. Fy=420MPa. 1. Determine the horizontal shearing stress at 95 mm above the Neutral Axis.2. Determine the spacing of the bolts.
Select a 9-m long W10 section of A572 Grade 50 steel to support a tensile load of PD = 490 kN and PL = 580 kN. The member is assumed to have one line of holes in each flange and two lines of holes in the web for 19 mm diameter bolts. There will be four bolts in each line 100 mm on center. Neglect block shear
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the spacing of rivets in mm.
A C7x9.8 tension member (A36) is connected to a 3/8-inch thick gusset plate (A36) as shown below. Compute the available block shear strenghth of the gusset plate for both LRFD and ASD
A C7 steel x 9.8 tension member is connected to a ⅜ inch thick gusset plate as shown. Both the member and the gusset plate are A36 steel. Compute the available block shear strength of the tension member.
3.6-5 Use load and resistance factor design and select an American StandardChannel shape to resist a factored tensile load of 180 kips. The length is15 ft, and there will be two lines of 7⁄8-in. diameter bolts in the web, asshown in Figure P3.6-5. Estimate the shear lag factor U to be 0.85. (In apractical design, once the member and bolt layout are selected, the valueof U could be computed and the member design could be revised if necessary.)Use A36 steel.
Select the lightest WT180 available to support a factored tensile load of 1112 kN. Assume there are two lines of M22 bolts in the flange (at least three bolts in each line 100 mm on center). The member is to be 9.144 m. Use LRFD.
Design a 11 ft single-angle tension member of A992 steel, to support a dead tensile load of 25k and a live tensile load of 45k. The member is to be connected to one leg only with 5/8-in bolts (4 in a line 3" on center) Then assume a reasonable distance for bolts to the edge of the angle and check the block shear. *Please clearly show all steps so I can follow along.
Select a 30-ft long W12 section of A992 steel to support a tensile servicedead load of 130 kips and a tensile service live load of 110 kips. Asshown in the figure, the member is to have a two lines of bolts in eachflange for 7/8-in bolts (at least three in a line 4 in. on center).Use Fy = 50 ksi and Fu = 65 ksi.